Back to Articles
by Gareth (Gdominy)
This was my first solo attempt at
creating an aquarium stand. In the end it worked out fairly well and I have
learned enough that I feel I can tackle a stand for the 135 Gallon tank that
we will be purchasing shortly.
total this project cost approximately $85 Canadian for the Stand, Canopy and
all the electronics (light fixture and bulbs).
Thats about it, I purchased all
of my parts from Home Depot and even had them cut the
wood for me. This makes it easier if you dont have a large vehicle to move
a 4 x 8 sheet of plywood around.
The Aquarium Stand
Step 1 Measure the aquarium
I dont feel I need to stress the
old carpenters adage measure twice, cut once so well skip the preamble.
When measuring the 45 Gallon aquarium used for this stand I allowed for ¼ of
play around the tank. Even with this, it turned out to be a close fit.
Youre typical aquarium may not be
the actual dimensions they list. For instance, a local company here in <state><place>Victoria</place></state>
manufactures high quality aquariums. They use the standard 1 foot width for
tanks and various standard lengths (20 24 30 36 48 72 etc). What we discovered
(as many other DIYs have before) was the listed dimensions were actually
the dimensions of the GLASS not the actual black plastic trim around the bottom.
now we have a tank that is actually 12 ½ by 48 ½.
Step 2 Plan your cuts
As mentioned above, you only get
one real shot at this, this design really used most of the wood and leaves little
room for error. This is why I got Home Depot to cut these for me.
I managed to get the
single sheet cut into the following pieces (roughly):
in mind that a saw blade takes off an eighth of an inch with each cut.
Step 3 Assembly
Glue is your friend. People often
times neglect to use wood glue when building something for home, it is however
incredibly strong, and should never be forgotten. Another important consideration
is the need to pre-drill the holes for your woodscrews. As a screw twists into
the wood, it will try to separate the layers and can quickly ruin any hope of
a strong joint.
Before you start to screw or glue
anything together you need to figure out where you want your vertical supports
to be. The two outside supports will obviously be on the outside of the box
that will support your stand. The middle two boards are up to you for spacing.
I chose to leave a larger cavity in the center of my design to allow for larger
objects to be stored under it.
the assembly by running a bead of glue up the 16 edge of one of the 16 x 12
pieces. Affix this to the 16 x 48 board
Any professional carpenter would
probably look at you and Ewwww a butt joint. But
hey, if youre reading how to build one of my stands, youre certainly not
a professional carpenter!
Once the boards are attached you
should pre-drill a hole at the top and bottom of the joint and screw it together.
It is best to do this while the glue is still wet, so any excess can bleed
out as the wood tightens together.
Continue this process for all four
boards until it looks like this. This will form the back of the stand and the
vertical risers to support the aquarium.
Let the glue dry, then
sand the edges. Run a bead of glue along the top edges of the structure and
place one of the 48.5 x 13 boards on top. This will become the top of the
stand. Predrill the holes for your screws and then
screw the whole thing together.
Once the glue has dried, flip the
structure over and repeat for the bottom. Your stand should now appear as follows:
At this point you can install a kick
plate if you want, I chose to leave this out (out of laziness more then anything).
If you wanted, simply build a rectangle out of a 2x4 or a 2x2 and attach it
to the bottom (leaving a few inches gap from the edge).
You can now add the trim that masks
the black plastic edge of the tank bottom. Run a bead of glue along the top,
front edge of the stand. Once that is complete, attach the 50 x 3 strip to
this. Make sure that the strip is flush with the bottom of the top piece of
wood and that you have allowed ¾ on each end for the end guards. Use finishing
nails to tack it into place.
Next, run a bead of glue along the
ends of the box and attach the end guards (these are the 13 x 3 strips). Tack
into place using finishing nails. Youre stand (when looking from the top down
should now look like this
from the front:
The Aquarium Canopy
The canopy isnt too difficult.
In fact its fairly simple. Very few screws are required for the construction;
however glue and finishing nails will be required.
we already know the dimensions of the aquarium from the previous steps, and
our wood is already cut, we can skip straight to the assembly.
Step 1 Assembly
a bead of glue along one edge of the 50 x 5 plank. Attach this to the 50
x 6 plank as follows:
You will want to use a few screws
(4?) to secure this joint. This structure is going to become the opening portion
of the lid and needs to be strong and rigid.
Glue the 5 x 13 and 5 x 6 pieces together as follows (tack together using
will need two of these, as they will make up the back corners of the canopy
(make sure that you second one is a mirror of this one)
Run a bead of glue along the 6 pieces
and up 8s of the 13 pieces, DO NOT RUN GLUE ALONG THE WHOLE LENGTH OF THE
PIECE. Attach the 8 x 50 plank to these corners so it appears as follows:
Allow the glue to set completely
before continuing. Once the glue has set, take the opening portion of the canopy
we created early and place it so the 5 plank portion is hanging over the side
boards, and the 6 plank is on the top edge to edge with the 8 plank.
Take your 36 piano hinge and center
it on the joint between the 6 and 8 planks. Once centered, use your brass
finishing screws to attach it to the wood. Once complete it should look like
Now, flip the canopy over so it is
top down. We have to attach the fluorescent fixture. Make sure before you
buy your fixture that you have one that will fit, not all fixtures are created
equal. Screw your fixture in place, and follow directions for wiring it.
In my case I had purchased a fixture
that needed to have its ballast wired to a 110V power
source. This is a regular kitchen fixture, and came with ballast covers to
prevent moisture from entering.
attempt to do any electrical wiring while the circuit is hot.
I will not be providing details on
wiring here, as no two fixtures are created equal. Consult with an electrician
before attempting anything like this on your own.
You will need to attach a runner
to keep the canopy from sliding down the tank. I used some of the leftover
scrap to create 2, 1 strips that run along the 13 end pieces. This allowed
the canopy to slip over the top of tank just enough to cover the black plastic
You can finish this stand in any
way you like. Typically a basic wood stain will look quite nice, and will draw
out the natural patterns of the wood.
Have a question about this article? Discuss it on the board!