What sealent is good for DIY yeast co2 system?
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment


Reply
 
Thread Tools Display Modes
Old 02-25-2013, 02:30 AM   #1
reconmarui
Algae Grower
 
PTrader: (0/0%)
Join Date: Sep 2012
Location: USA
Posts: 65
Default

What sealent is good for DIY yeast co2 system?


What sealant works the best for this system? Also how can I tell if it is working?
reconmarui is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 02-25-2013, 07:15 AM   #2
sepulvd
Planted Member
 
PTrader: (0/0%)
Join Date: Mar 2012
Location: japan
Posts: 157
Default What sealent is good for DIY yeast co2 system?

are you taliing about what to use to prevent co2 leaking from the cap where the tubing goes thru. if yes i usually use crazy glue around the tube snd cap. never had leaks
sepulvd is offline   Reply With Quote Quick reply to this message
Old 02-25-2013, 11:02 PM   #3
Bandit1200
Planted Tank Enthusiast
 
Bandit1200's Avatar
 
PTrader: (4/100%)
Join Date: Dec 2010
Location: Houston, Texas
Posts: 608
Default

I used hot glue on mine.
Bandit1200 is offline   Reply With Quote Quick reply to this message
Old 02-25-2013, 11:09 PM   #4
m00se
Wannabe Guru
 
m00se's Avatar
 
PTrader: (5/100%)
Join Date: Jan 2011
Location: Syracuse, NY
Posts: 1,481
Default

No glue. Just drill a hole under-sized for the tubing, cut the end of the tubing diagonally so you make a sharp angled end, and pull it through the cap with a pair of pliers. Air tight and fool proof.



m00se is offline   Reply With Quote Quick reply to this message
Old 02-25-2013, 11:55 PM   #5
newms
Algae Grower
 
PTrader: (1/100%)
Join Date: Sep 2012
Location: Florida
Posts: 57
Default

I get leaks sometimes out of the threading area of the bottle. I use aquarium silicone to seal it up, however the stuff isn't cheap. I like the idea of hot glue that was mentioned above.

I check for leaks by placing the whole setup under water in my water change bucket and blowing into the end where the gas would normally come out. If there is a leak, you will see the little bubbles streaming out of it. If the system isn't working, 99% of the time it is because of a leak.

Last edited by newms; 02-25-2013 at 11:56 PM.. Reason: clarity
newms is offline   Reply With Quote Quick reply to this message
Old 02-26-2013, 12:40 AM   #6
mistahoo
Planted Tank Enthusiast
 
mistahoo's Avatar
 
PTrader: (11/100%)
Join Date: Apr 2012
Location: Houston,Tx
Posts: 747
Default

GE Window and door silicone
mistahoo is offline   Reply With Quote Quick reply to this message
Old 02-26-2013, 01:01 AM   #7
thesawguy
Planted Member
 
PTrader: (9/100%)
Join Date: Dec 2011
Location: USA
Posts: 258
Default

I will agree with the m00se method. But will add that with the tubing I used it eventually got stiff and leaked at the part that was squeezed, so I would just pull it down a little further and create a new squeeze point. Silicone and super glue failed for me after a few months.
thesawguy is offline   Reply With Quote Quick reply to this message
Old 02-26-2013, 01:24 AM   #8
kaaayd
Algae Grower
 
PTrader: (0/0%)
Join Date: Apr 2012
Location: west orange, NJ
Posts: 12
Default

I have tried silicone and just a tight fitting tube. Both have failed for me. What I have done now (and has worked consistently for the ones I made for friends) is:

Use a Gatorade bottle. I found that soda bottles tend to leak through the cap sometimes. It caused me hours of frustration until I used a Gatorade bottle (I use the bottles that are close to 2 liters and also the one that's a gallon or something). Seals perfect every time.

Drill the hole in the cap, put the tube through, then wrap some duct tape around the cap. Make sure there is a decent amount of tape above the cap. Fill it with Gorilla Glue (doesn't have to be to the top, but thick enough). Let it dry over night.

This will definitely work. I have never had a problem with this method.
kaaayd is offline   Reply With Quote Quick reply to this message
Old 02-26-2013, 03:15 AM   #9
reconmarui
Algae Grower
 
PTrader: (0/0%)
Join Date: Sep 2012
Location: USA
Posts: 65
Default

I used a combination of excessive amounts of jb weld water proof putty that hardens(had it lying around) and hot glue, in excessive amounts too, holding up well so far or at least I'm getting bubbles
reconmarui is offline   Reply With Quote Quick reply to this message
Old 02-26-2013, 07:09 AM   #10
mistahoo
Planted Tank Enthusiast
 
mistahoo's Avatar
 
PTrader: (11/100%)
Join Date: Apr 2012
Location: Houston,Tx
Posts: 747
Default Re: What sealent is good for DIY yeast co2 system?

Drill a hole in the top. Use a nylon fitting and screw it on. Then stick the tubing onto the nipple. Truly failproof compared to anything mentioned on here so far. No leaks and you can remove it if needed or just swap the caps.

Sent from my spaceship using Tapatalk 2.
__________________
SunSun Pimp #82|RAOK Club Member #89|Eheim Pimp #543

210G|1.5G Iwagumi DSM|5G Fluval Chi
mistahoo is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:40 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012