twin 29g tanks on metal stand...pic heavy!
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > General Planted Tank Forums > Tank Journals


Reply
 
Thread Tools Display Modes
Old 09-17-2011, 07:49 PM   #1
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

twin 29g tanks on metal stand...pic heavy!




Ok, I'm going to start a journal on two 29g tanks I bought at the Petco sale. I'm using my late father's metal stand for sentimental reasons. It was pointed out to me that the clearance on the bottom tank will be tight, and boy, it is! I have 4-1/2" of clearance between the top and the metal above it. I'm going to make it work, though. I'll be using a versa top (and I may make my own to give it a try) and a single or double T5NO. I guess a single, since I want low tech, low light tanks. Crypts, anubias, trident java fern, rocks & driftwood. These tanks will house small shoaling fish, up to two different schools per tank.
First, I wanted to raise the metal stand - the bottom tank was too low to really see. I bought a 2"x8"x8' at Lowes and built a basic base using brackets inside. I topped it with 3/4" plywood. No shear, no movement, and square.
Then I used Hardiebacker board on top of the ply and did a mosaic to match the tile floor I'm laying under the tanks. To be sure it was level I used a puck tile level during each step.
One pic shows the outdoor retaining blocks I made years ago for my garden. They were the inspiration to mosaic the base - I don't have a tile cutter, and it's fun to smash tile with a hammer! lol
These tanks are going in a spot that is between my kitchen & living room - against an exterior wall - so I choose tile I'd like to use in my kitchen and extended it under the tanks. I'm going to do the same for two 55s that I'm putting up later as a dividing wall between my living room and kitchen. I'm a slob when it comes to water changes, so I wanted tile under the tanks. As much mosaics as I've done, this is my first time laying tile. I put 1/2" ply over my existing subfloor (I want to strengthen my subfloor throughout my mobile home). Used 1/4" Hardieboard with the polymer thinset recommened, and ceramic tile. I was going to go with porcelain, but $$ was a consideration. Even my girlie 14.4v B&D cordless screwed the Hardiebacker screws in pronto - it's very easy to do!
So, now I'm waiting to grout.
__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 09-17-2011, 07:52 PM   #2
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

These are the brackets..



My cat laughs at my building skills...

__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-17-2011, 08:03 PM   #3
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

The backer board on the new subfloor - sorry the pic are so big! I'm still trying to figure out why sometimes I get the pics, and sometimes I get the links...

__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-17-2011, 08:05 PM   #4
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

The base, showing the ply top, the backer board, thinset, ready for tile!

__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-17-2011, 08:09 PM   #5
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

Mosaic is done, waiting to grout. The new tile floor is in the background, the tile level is checking the corners where the tank's feet will sit.

Level!
__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-17-2011, 08:12 PM   #6
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

The outdoor retaining wall I made by mosaicing concrete cap blocks. These have been outside for 4 - 5 years, and I forgot to seal the grout. Still holding up well! (sanded grout)
Can someone tell me how to add more than one pic per post? lol This will be 10,000 posts long! ; )

OK - it took me a while, but I think I've got the photo thing down... lol

__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 06:26 PM   #7
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default starting a DIY 3D background

Now I'm starting my first DIY 3D background for the bottom tank. I've never made one before, but I've been reading all I can on the cichlid sites.
I bought a sheet of blue insulation at Lowes ($10 per 4'x8' sheet by 1" thick). I had to slice & dice it in the parking lot to fit in in my little Hyundai Accent! lol I didn't know insulation was covered in thin plastic - I removed it. Nothing I've read on the sites mentioned it, but I think you probably have to for a tank.
I used the 29 tank as a template, and cut two pieces. One is a solid backing - the bare canvas, if you will. The second piece is for added depth, and to allow me to cut out a shape to accomodate the intake of my HOB.
Next I drew rough rock shapes/directions on the third piece, and cut out the rough shapes into individual smaller shapes. It was much easier for me to carve that way. So I wouldn't forget where things went, I wrote letters on the jigsaw pieces & back to match them up. After I siliconed them down, I went back in some spots and carved even deeper into the sheet below (not the base sheet). I like the depth it gives.
All I ended up using was a steak knife - I have a propane torch and was going to smooth the edges with it, but I like the jagged look. Maybe I'll use the torch a little next time (I have two tanks to do). So this has 3 sheets - one solid base sheet, one middle sheet, and the top sheet that I cut the rocks out of. The little accent pieces I added to the very top are from the scraps left over from carving.
It's all glued up with GE1 silicone, when it hardens I'll tweak the carving. Btw, when I glued the sheets and "rocks" up, I spread the silicone out with a bit of cardboard - so there is 100% contact on all pieces of styro.
next - experimenting with Drylok and quickcrete colorants!








__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 06:55 PM   #8
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

Ok, I lied! I couldn't resist trying out the propane tank - I lightly "dusted" the surface, and I'm glad I did. I may go back and resharpen a few edges, but overall I like the "water softened" effect.
Guess I'll wait until tomorrow to start the Drylok process...
__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 07:07 PM   #9
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default Final dry fit of the 3D BG



I'm going to carve a little more out around the intake, esp. on the left side so it's a smoother transition. Some tweaking of the carving, and I'm good to go onto the next step!

I've been thinking about adding pieces of styro like a "bridge" over the tube of the intake. I couldn't put the whole BG forward enough to hide it, because the 29 is so shallow a tank. But I may put pieces over the tube, leaving the grill exposed. That way I'll still be able to remove the filter & intake for cleaning, and all but the grill will be hidden. What do you think? (however it would be easier to hide the intake with a sword or java ferns and driftwood- my first choice - lol)
__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 07:09 PM   #10
wkndracer
Planted Tank Guru
 
wkndracer's Avatar
 
PTrader: (68/100%)
Join Date: Mar 2009
Location: Citrus County,Florida
Posts: 6,180
Default

great DIY thread Thanks!
__________________
The Fraternity of Dirt
If at first you don't succeed,,, keep kicking it
RubberSideDownOnTheLanding,
2-75g planted, 5-55g planted, 5-20g planted, 110g w/30g sump, 8-10g, Refugium, doghouse/newbie
2012 update adding table top pleco pans & a 90g (Nutz)
wkndracer is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 08:32 PM   #11
jwm5
Planted Tank Obsessed
 
PTrader: (0/0%)
Join Date: May 2010
Location: Virginia
Posts: 334
Default

wow a new (to me) fake rock method, definitely watching this one. looks good so far.
jwm5 is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 08:50 PM   #12
scapegoat
Planted Tank Guru
 
scapegoat's Avatar
 
PTrader: (15/100%)
Join Date: Jun 2010
Location: philadelphia, pa
Posts: 2,230
Default

def try to hide the intake as much as possible. i'd also consider making a "rock" that goes under the outflow to resemble a cliff edge
scapegoat is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 10:17 PM   #13
driftwoodhunter
Planted Tank Guru
 
PTrader: (23/100%)
Join Date: Jul 2011
Location: Christiansburg, Va
Posts: 2,756
Default

scapegoat - I thought about making a ledge/cliff under the outflow - I thought it would be cool to have it slightly divide, so the water flow wouldn't go straight in/down.
Hmm, mayby the creative juices will turn back on tonight - lol.
jwm5, I found about about DIY 3D backgrounds because someone on this site had a link to a cichlid site. I don't remember who it was now, but if you google "DIY 3D background" there are amazing (and sometimes not so much) things made for aquariums and terrariums. It's fascinating! Concrete was used for years, but Drylok has become the norm - it doesn't require soaking to leach out chemicals - it's made to line masonry but also potable water/birdbaths, etc.
I haven't opened up the can yet so I don't know how it is to work with, but I've read it's white and like thickened latex paint. They can tint it at the store for you, but I bought three colors of concrete tint to experiment with - charcoal, terra cotta, and buff. You can add sand & grit to it for texture, too!
__________________
The Fraternity of Dirt # 7 - Daughter of the Dirt - Canon Club #018
Twin 29g Dirt Tanks on an Iron Stand - DIY 3D Backgrounds
http://www.plantedtank.net/forums/ta...stand-pic.html
The Behemoth - 125 dirt tank
http://www.plantedtank.net/forums/sh...d.php?t=199772
driftwoodhunter is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 10:41 PM   #14
OverStocked
Planted Tank Guru
 
OverStocked's Avatar
 
PTrader: (76/94%)
Join Date: May 2007
Location: SoDak
Posts: 10,732
Default

I've been wrong about a lot of things.... but no way in the world would I put two 29 gallon tanks on a stand sitting on that block......

I think you've underestimated the 300 lbs that will be sitting on it.


The backgrounds are cool, though.
OverStocked is offline   Reply With Quote Quick reply to this message
Old 09-23-2011, 10:50 PM   #15
cableguy69846
Planted Tank Guru
 
cableguy69846's Avatar
 
PTrader: (8/100%)
Join Date: Dec 2010
Location: Chicago, IL
Posts: 4,986
Default

Very nice. I will be following along for the ride on this one.

One tip about the Drylok. I have not used it yet, but on all the reptile forums I am part of, everyone says that if it is going to be constantly wet, it should be covered in something that will waterproof it further. Having said that, may I suggest a layer of clear silicone after you paint it all? Just a thought. Now enough of my rambling and inexperienced tips. ON WITH THE BUILD!
__________________
The Fraternity of Dirt #39
Just because its dirt doesn't make it low tech

Cable's Madness
Fish tanks are like cups of coffee, one is never enough.
"What the smeggin smeg's he smeggin' done now?!" - Lister
cableguy69846 is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:56 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012