Complete Leak Check, CO2 pressurized system - Page 7
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment


Reply
 
Thread Tools Display Modes
Old 03-06-2013, 06:07 AM   #91
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

Quote:
Originally Posted by Mathman View Post
Bettatail please elaborate more as I do not understand what "back screw" you are mentioning.

Here's a comparison of my hpt 207C and the Milwaukee

the back of the regulator, there is a screw with a screw head cap fitting on top, and usually there is sticker says "do not adjust".
apparently it was adjusted so the output pressure can not pass 20psi, otherwise it should be around 80 psi max output as manufacture default setting.

add: you must be sure that your HPT 270 is a "C", not "A", so you can play with the back screw, and don't trust the LP gauge(max reading) to decide if it is a "C" or "A".
Bettatail is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 03-06-2013, 06:11 AM   #92
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system



Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:11 AM   #93
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

Bettatail is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:13 AM   #94
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system

Clockwise or counter clockwise...also, do I do this having the reg attached to the co2 tank?
Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:15 AM   #95
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,432
Default

Quote:
Originally Posted by Mathman View Post
I like that setup bettatail. I have another huge problem. I have that same solenoid on your pic but the tiny wires broke by the black casing and there's no way for me to connect the wires. Any way this can be fixed? I don't like that model of the burkert solenoid and shouldn't have purchased it.
Wire to wire resoldering or for a cleaner look, just open up the case and resolder the wires completely.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:16 AM   #96
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default

Quote:
Originally Posted by Darkblade48 View Post
Wire to wire resoldering or for a cleaner look, just open up the case and resolder the wires completely.
That's a weekend project. Haha.

Is the back screw suppose to be hard to move? I'm scared to turn it too much.

Last edited by Darkblade48; 03-06-2013 at 09:02 AM.. Reason: Multiple posts within minutes of each other - please use the edit button in the future
Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:40 AM   #97
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system

Yay...with some playing around I was able to set it to 80psi
Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:49 AM   #98
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

groves, safety glasses, or mask if you have one.

1. put the relief valve back on.
2. take out the back screw cap
3. put the system on the co2 tank, but keep the co2 tank shut.
4.adjust the back screw with allen key.
a. remember/mark the original position of the screw.
b. turn it clock wise to increase the pressure, 1/4 of a complete turn
c. turn on co2 tank, charge reg with 800 psi, then shut off the co2 tank.
d. turn the front handle to check max output(post body kit shut)
e. release all pressure in the regulator, set the front handle to off position.

repeat a -- e, until the max output goes up to what you desire, but not excess 80psi.

if any step you see the relief valve start releasing gas, stop and go the opposite way until the relief valve stop venting gas, and no further try to increase the max output pressure.
finally, Do it on your own risk.
Bettatail is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:49 AM   #99
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

Quote:
Originally Posted by Mathman View Post
Yay...with some playing around I was able to set it to 80psi
that is fast, even before I made the instruction, lol.
Bettatail is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 06:52 AM   #100
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system

I loosen the screw just a bit, turned the front knob (regulating valve) to increase it to 80psi, then tighten the back screw. I did this while having the reg attached to the co2 tank completely opened.

I did not remove the back knob completely.
Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 07:00 AM   #101
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default



probably the back screw or the spring in the back sit at the wrong position(inside), a loose and re-tighten set them back the right place.
Bettatail is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 07:06 AM   #102
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system

I hope everything is working fine. Ill check tomorrow mornkng if there's a change in pressure for both gauges.

Next project is to fix the burkert solenoid.

Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 07:09 AM   #103
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

cut the other wire, and find two small sharp point screws, stainless steel and proper size, drill into the plastic, use the screw heads as prongs.
Bettatail is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 07:11 AM   #104
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 364
Default Complete Leak Check, CO2 pressurized system

That's an interesting idea. Will it work? Is this something you've tried?
Mathman is offline   Reply With Quote Quick reply to this message
Old 03-06-2013, 07:17 AM   #105
Bettatail
Planted Tank Guru
 
Bettatail's Avatar
 
PTrader: (87/98%)
Join Date: Feb 2009
Location: San Francisco
Posts: 2,530
Default

no, never try, but it will work, just make sure the screws are right size, drill where the wires embed, but don't drill too deep, you don't want to damage the coil.
Bettatail is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 07:29 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012