fluval 404 as a diffuser
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment


Reply
 
Thread Tools Display Modes
Old 01-16-2004, 04:43 PM   #1
wildy
Algae Grower
 
PTrader: (0/0%)
Join Date: Jan 2004
Posts: 10
Send a message via MSN to wildy
Default

Im using a fluval 404 as a diffuser for my 150 g tank my ph is 7.3 and my k.h is 1.5 , but the ph isnt dropping , im putting abouut 30 bubbles per minute into my tank from my bottle any ideas...is the gas escaping from the fluval ????
wildy is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-16-2004, 06:02 PM   #2
GulfCoastAquarian
Planted Tank VIP
 
GulfCoastAquarian's Avatar
 
PTrader: (6/100%)
Join Date: Jul 2002
Location: Winston-Salem, NC
Posts: 3,578
Send a message via ICQ to GulfCoastAquarian Send a message via Yahoo to GulfCoastAquarian
Default

Are you just letting the air bubbles get sucked into the intake? Or is the Fluval pushing a reactor? If you inject gas into a top-mounted impeller canister filter (like the Fluval), the gases can collect in the magnet chamber, causing it to run "dry" and overheat.
In spite of the danger of damaging your filter, I'm surprised you're able to diffuse the CO2 at all through your Fluval. As long as you don't see CO2 come out the other end of a CO2 reactor, you know it is dissolving into the water (or collecting in a chamber, to dissolve later). With a low KH like 1.5dKH, I would worry that the pH would drop TOO quickly.
How long have you been running CO2 into the tank?
__________________
- Sam P -
plantedtanker in limbo - all tanks currently in storage
GulfCoastAquarian is offline   Reply With Quote Quick reply to this message
Old 01-16-2004, 07:00 PM   #3
Wasserpest
Are these real?
 
Wasserpest's Avatar
 
PTrader: (176/100%)
Join Date: Jun 2003
Location: Monterey, CA
Posts: 15,138
Default

What I have gathered from playing around with canister filters as reactor chambers, injecting CO2 into the inlet will not lead to accumulation of air in the magnet chamber. At least in the case of Filstars (I am assuming the Fluvals use a similar design). The CO2 enters the canister housing, and would have to float down to the bottom, pass through all filter media, and then collect in the impeller chamber. Any CO2 reaching the impeller would be immediately pushed out through the tubing into the tank.
Instead, it remains on the top in the outer housing, and is dissolved there. The only negative effect I could see was that the noise level went up, due to the water rushing in and mixing with the CO2.
This principle is often used with powerheads sucking the bubbles in and smashing them up. Here, there is a danger of air/CO2 collecting in the impeller chamber in the case of power outages, which might dry-run the power head. Not so with canister filters.

So I think the bubbles are dissolving. 150 gallons is a lot of water... Is the Fluval the only filter? Or are there others that possibly create surface agitation? Perhaps you only have to increase the bubble count, very slowly, while monitoring pH.
Wasserpest is offline   Reply With Quote Quick reply to this message
Old 01-16-2004, 07:57 PM   #4
Raul-7
Wannabe Guru
 
Raul-7's Avatar
 
PTrader: (4/100%)
Join Date: Oct 2003
Location: Lomita, CA
Posts: 1,691
Default

So Wasserpest, I can just run my C02 into my canister intake without any hazards..except for the audible noise?
Raul-7 is offline   Reply With Quote Quick reply to this message
Old 01-16-2004, 08:08 PM   #5
Wasserpest
Are these real?
 
Wasserpest's Avatar
 
PTrader: (176/100%)
Join Date: Jun 2003
Location: Monterey, CA
Posts: 15,138
Default

That is my experience.

Having said that... I use an external reactor on the outlet side now, both because of the noise I got when bubbling into the inlet, and to reduce the fine oxygen bubbles coming out of the filter every afternoon.
Wasserpest is offline   Reply With Quote Quick reply to this message
Old 01-17-2004, 04:43 AM   #6
wildy
Algae Grower
 
PTrader: (0/0%)
Join Date: Jan 2004
Posts: 10
Send a message via MSN to wildy
Default

i run 2 fluvals , 1 each side and yes co2 into the intake, with a little surface aggitation from 1 fluval spray bar the othere in the tank water. so IYO it will work just increase the co2?????
wildy is offline   Reply With Quote Quick reply to this message
Old 01-17-2004, 01:53 PM   #7
WfxXx
Planted Tank Guru
 
WfxXx's Avatar
 
PTrader: (125/100%)
Join Date: Dec 2003
Location: USA
Posts: 3,037
Send a message via ICQ to WfxXx
Default

I use 2) Eheim 2213 canisters on my tank, with one being the defuser, I cant find a better way to desolve c02, and even if quote if it did run dry and fry the impeller, its only $10, I cant build or buy a better defuser for that, I adjust c02 levels by adjusting spraybar for more or less surface movement, I did a test, first I let it run for awhile with spraybar about 2 to 3 inches below surface pointing up creating surface movement, pH would hover around 7/7.2
I then lowered a bit more and pointed spraybar to back glass, within a day the pH dropped to 6.4/6.6
Raise and point back to surface would rise back to 7-ish etc

So, in my estimation, canister with media is absolutly the best defuser by far.
WfxXx is offline   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Fluval 404 MSF and Marineland Magnum 350 Review GDominy Equipment 6 05-28-2009 02:04 AM
Extremely unscientific diffuser attempts; MacTech DIY 15 10-22-2004 08:48 PM
DIY intake/spraybar for 20g w/ Fluval 104 Daemonfly DIY 14 05-05-2004 08:56 PM
Hagen CO2 diffuser EvilKen Equipment 32 12-08-2003 09:52 PM
Freakin Fluval GulfCoastAquarian Equipment 15 04-25-2003 09:32 PM


All times are GMT. The time now is 08:36 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012