Want to DIY a co2 reg - Page 3
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY


Reply
 
Thread Tools Display Modes
Old 02-01-2013, 01:04 PM   #31
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default

Want to DIY a co2 reg


Anthony,

Thanks for the clarification. Now, lets check for understanding...the PDF for the Victor VTS 250 series indicates the following:



Is the working pressure of the manifold you mentioned, the range I see in this picture? For example, the 250C has a range of 4-80psig and the 250D series has 5-125 psig.

If my understanding is correct, a lower gauge that goes up to 100psi may work for both of these series since, for our purposes, we will never go past the 100psi?

In other words, can a 100psi lower gauge be installed on a 250D series or is a 200psi a best choice?

Thanks!

~Cristian~
Mathman is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 02-01-2013, 05:33 PM   #32
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

Anyone?
Mathman is offline   Reply With Quote
Old 02-01-2013, 07:08 PM   #33
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Quote:
Originally Posted by Mathman View Post
Is the working pressure of the manifold you mentioned, the range I see in this picture? For example, the 250C has a range of 4-80psig and the 250D series has 5-125 psig.
I do not believe I mentioned a manifold; only the delivery pressures.

Quote:
Originally Posted by Mathman View Post
If my understanding is correct, a lower gauge that goes up to 100psi may work for both of these series since, for our purposes, we will never go past the 100psi?
Yes.

Quote:
Originally Posted by Mathman View Post
In other words, can a 100psi lower gauge be installed on a 250D series or is a 200psi a best choice?
Yes, it can. You can leave the 200 PSI gauge on as well; I use a Victor that has a 200 PSI low pressure gauge and it increases in (minor) increments of 5 PSI and major increments of 20.


Quote:
Originally Posted by Mathman View Post
Anyone?
Calm down, most of us have work to do
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-01-2013, 08:12 PM   #34
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

Haha...thanks buddy. I'm at work too but I'm just too distracted.
Mathman is offline   Reply With Quote
Old 02-01-2013, 10:36 PM   #35
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

Aside from eBay...what's another good place to find good quality low pressure gauges with a maximum 100psi reading?

Also, what is the size for the ports in the 250 series where the gauges connect to?

Thanks.
Mathman is offline   Reply With Quote
Old 02-01-2013, 11:49 PM   #36
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Quote:
Originally Posted by Mathman View Post
Aside from eBay...what's another good place to find good quality low pressure gauges with a maximum 100psi reading?

Also, what is the size for the ports in the 250 series where the gauges connect to?

Thanks.
You may be able to find a local welding store that carries them.

As for the sizing, don't quote me on it, but I believe most are 1/4" NPT.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-01-2013, 11:53 PM   #37
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

What's considered a good price for them? Thanks
Mathman is offline   Reply With Quote
Old 02-02-2013, 12:57 AM   #38
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Quote:
Originally Posted by Mathman View Post
What's considered a good price for them? Thanks
That's hard to say; I've seen decent ones go from $10-20, but stainless steel ones can cost significantly more.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-02-2013, 11:40 PM   #39
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

I'm looking over the PDF file for the VTS 250 series...

I boxed in red what I think is the maximum working pressure for each model...Am I correct?

For example, the VTS 250D has a working pressure of 5-125psig. So, in the event that one wants to replace the LPG the best choice is to go with one with a maximum 200psi... Correct?

I've noticed that some people use 100 psi or recommend to use this gauges...isn't that a risk? What if one accidentaly goes over the 100psi mark...the gauge will break. Right?

Edit:

Mathman is offline   Reply With Quote
Old 02-03-2013, 12:27 AM   #40
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Quote:
Originally Posted by Mathman View Post
I boxed in red what I think is the maximum working pressure for each model...Am I correct?
I do not see anything.

Quote:
Originally Posted by Mathman View Post
For example, the VTS 250D has a working pressure of 5-125psig. So, in the event that one wants to replace the LPG the best choice is to go with one with a maximum 200psi... Correct?
This is correct to some degree; you can replace the low pressure gauge with one that is lower than the maximum working pressure (see below).

Quote:
Originally Posted by Mathman View Post
I've noticed that some people use 100 psi or recommend to use this gauges...isn't that a risk? What if one accidentaly goes over the 100psi mark...the gauge will break. Right?
Yes, if you go over the 100 PSI mark accidentally, while the regulator itself will be fine (since it was designed to handle that delivery pressure), you will break the low pressure gauge.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-03-2013, 12:36 AM   #41
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

Picture has been posted.

So...what maximum LPG is considered to be the best to give you the best control over reading pressure?

Thanks!
Mathman is offline   Reply With Quote
Old 02-03-2013, 02:46 AM   #42
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Quote:
Originally Posted by Mathman View Post
Picture has been posted.

So...what maximum LPG is considered to be the best to give you the best control over reading pressure?

Thanks!
Yes, the boxed values represent the working pressures (minimum and maximums) of those particular regulator models.

I would say 200 PSI should be the maximum reading on the low pressure gauge (not the maximum delivery pressure of the regulator). Anything higher, and it will become difficult to see how much you are increasing/decreasing the working pressure by.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-10-2013, 08:25 AM   #43
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

I'm so about to throw this reg away...i purchased this VTS 250d on eBay and have been trying to remove the LPG and inlet but its practically impossible. My hands hurt from trying to turn the wrench but no luck. Any suggestions? I do not have a bench vise.

Thanks

Mathman is offline   Reply With Quote
Old 02-10-2013, 10:00 AM   #44
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Japan
Posts: 9,263
Default

Check to make sure there is no (red) Loctite around the low pressure gauge.

If you do not have a bench vise, you are in a bit of trouble. You will probably need one to get it off.

You can try a mechanic, they should have the tools.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is online now   Reply With Quote
Old 02-10-2013, 04:06 PM   #45
Mathman
Planted Tank Obsessed
 
Mathman's Avatar
 
PTrader: (0/0%)
Join Date: Apr 2009
Location: Los Angeles, CA
Posts: 363
Default Want to DIY a co2 reg

There's is no red loctite residue...ill try and see if my local mechanic would do me a favor. Thanks Anthony.
Mathman is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 05:46 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012