LED light fixture for 2-gallon tank using modularled.ca components
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY


Reply
 
Thread Tools Display Modes
Old 11-12-2012, 02:43 AM   #1
tjhd36
Newbie
 
PTrader: (0/0%)
Join Date: Nov 2012
Location: Ohio
Posts: 1
Default

LED light fixture for 2-gallon tank using modularled.ca components


I wanted to build an LED light fixture that would fit a 2-gallon tank, support demanding species like Hemianthus callitrichoides, and be affordable. I had limited DIY experience, but I found components from modularled.ca that made the project tractable. Photos below show the fixture and diagram how it was built.

Perspective view
https://picasaweb.google.com/lh/photo/G4UAawvpp-YCBebZ1o_6PtMTjNZETYmyPJy0liipFm0?feat=directlink

Top view
https://picasaweb.google.com/lh/photo/LQXQ2CCKbZdLcLz3BQjE2NMTjNZETYmyPJy0liipFm0?feat=d irectlink

Front view (including tank)
https://picasaweb.google.com/lh/photo/WqluYFSpKmpJmPogTyi_JdMTjNZETYmyPJy0liipFm0?feat=d irectlink

Total cost was about $85. This cost does not include tools and supplies. Working continuously, assembly would probably take 5-10 hours (excluding dry times for adhesives and solvents).

The fixture has been in use for 5 months. It has supported a wide range of species (Cabomba pulcherrima, Eleocharis parvula, Hemianthus callitrichoides, Limnophilia indica, Ludwigia arcuata, Ludwigia palustris, Rotala rotundifolia, Myriophyllum tuberculatum). Growth has been relatively lush—I’ve gotten a good carpet of H. callitrichoides. The light is also strong enough to give yellowish-orangish color to L. arcuata, L. palustris, and R. rotundifolia. I dose 0.15 mL Flourish twice weekly and use DIY CO2. Livestock is Neocaridina heteropoda var. red.

Components:
-4 LED Moonlight kit ($42 + $12.66 shipping; modularled.ca)
*2x2 Cool White XP-G (specially requested for additional $2 because kit includes 2x 2 XP-G Royal Blue by default)
*1x Moonlight Driver with Power Cord
* 1x Start & End Kit
* 1x 4 inch Standard Connector
* 2x 12 inch Extension Connector
-4x60 Degrees LED Lens ($4 ; modularled.ca)
-10”x1” Heatsink ($9; modularled.ca)
-1/8” thick acrylic sheet ($2)
-2xbookshelf brackets ($15; Rubbermaid)
-picture wire (already had)

Tools/supplies:
-power drill with 1/8” bit

-thermal adhesive (Arctic Silver)

-acrylic solvent
-screw driver
-razor blade knife
-aquarium-safe silicone
-superglue

Assembly instructions:
(i) Drill 2 holes on each side of heat sink using 1/8” bit (1/4” from edge; see photo for placement).
(ii) Attach 2x2 Cool White XP-G to heat sink using thermal adhesive (see
http://www.modularled.ca/videos/)
(iii) Connect together the 2x2 Cool White XP-G, start connector, end connector, standard connector, extension connector, and moonlight driver with power cord (see
http://www.modularled.ca/videos/). Test that LEDs light.
(iv) Attach lenses on LED boards using superglue (see
http://www.modularled.ca/videos/)
(v) Cut parts 1 and 2 for acrylic splash guard (see photo). Cut parts by scoring acrylic with razor blade knife and snapping the acrylic along the scored lines. Drill 2 holes on part 2 with 1/8 bit ( 1/4” from edge; see photo for placement). Make sure holes overlap those on heat sink.
(vi) Weld together parts 1 and 2 of splash guard using acrylic solvent.
(vii) Attach splash guard to heat sink using small drop of silicone
(viii) Mount bookshelf brackets on wall.
(ix) Using picture wire, hang heat sink (with LEDs and splash guard attached) from bookshelf brackets. Thread the wire through holes on heat sink and brackets. Twist the ends of wire to secure (see photo).
(x) Using zip ties, secure the extension connector on the moonlight driver and mount the driver to the bracket. Wrap the start connector around driver and secure zip tie around it. (This prevents the connector from being pulled out from the driver.) Secure the driver to the bracket by using a second zip tie.
tjhd36 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 11-12-2012, 04:05 AM   #2
Sd760
Planted Tank Enthusiast
 
Sd760's Avatar
 
PTrader: (0/50%)
Join Date: Apr 2011
Location: Humboldt co.
Posts: 500
Default

Awesome write up. Thanks
Sd760 is offline   Reply With Quote Quick reply to this message
Reply

Tags
2 gallon, cree, diy, led aquarium lights, modularled.ca

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:03 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012