DIY LED with MakersLED Heat Sink
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY


Reply
 
Thread Tools Display Modes
Old 07-20-2012, 06:36 AM   #1
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

DIY LED with MakersLED Heat Sink


So: research, research (see the DIY LED FAQ about all that mess), blah, blah, purchase, wait... BUILD! Woohoo! I'm working on this in my living room, by the way - I do not have a shop or any other space that works for this. Time becomes a huge issue, as my wife gets pretty annoyed with the mess and the odors of my gadgetry. I have to work quickly and efficiently to keep the peace As for the heat sink, some might feel it's not rightly DIY as it isn't built from whatever hunk of aluminum I could find, and they're partly right. I feel that this is more of an LED hobby kit than a proper DIY, but no worries It's still an awesome light!

The basic design is 2x18" heat sinks with 28 white Cree XT-E LEDs and 6 Bridgelux Moonlights all with 60 degree optics for an ADA 120P. I plan to hang this about 10"-12" above my tank. I went with 2@18" sections rather than 1@48" in case I wanted to downgrade these lights in the future for say, a 90-P. This setup is totally modular, so I can replace anything or tear it down and start over again.

I am using a DIM4 Controller for sunrise and sunset effects. I'm using 2 Inventronics 40W 700mA dimmable drivers (one for each Cool White and Neutral White), and the moonlights will be driven by the DIM4. Things I added are 2x12' medium duty extension cord for power to the drivers, one 8' section of 3/4" u-channel aluminum for joining and hanging the fixture, various nuts, bolts, eyebolts, wires, 60/40 solder, rubber grommets, heat shrink, plastic conduit, 1/4" clear acrylic sheet, sweat, and a little cursing here and there.

Pre-tinning my emitters and wires, to make assembly smooth and efficient:



Here's the heat sink. It's really a pretty gorgeous piece of aluminum. many might just be ok with a regular heat sink, but I really like the rugged construction, utility, and polish of this setup. It comes with plastic caps for the ends that can be drilled for wire access, etc. You'll see as I go along what I did with mine.



There I was lining the grooves with my bolts to get my pattern laid out. I had already drawn up a good diagram of how I wanted to lay out and wire the thing, so this was pretty easy. It was time consuming putting vinyl washers and nuts on the bolts. Ugh.

I also labeled each spot with the direction I wanted to mount the leads, so everything lined up smoothly. More on that adventure later. I used a wet-erase marker, and just wiped it off with alcohol and a paper towel.

I started to attach the emitters, one color at a time: Cool White, Neutral White, and Royal Blue for moonlights:



A dab of thermal grease to smooth things out...



...and ta-daaa!



I apparently didn't get any shots of the wiring process, but suffice it to say, It was relatively swift. My one hangup was when I decided to drive each color independently, so I replotted my wiring. This led to space issues when it came to my drivers. I originally didn't want to keep the drivers on the light itself, but necessity dictated that I do so. It works out ok, but the light weighs about 20 pounds now, haha... hanging this might be fun. So, the drivers for the cool white are on one heat sink, and the driver for the neutral white are on the other. This meant I had to creatively deal with hiding wires. Here's what I came up with.



I drilled through the base of the heat sink to the top and grommeted the hole with a rubber wiring grommet to prevent shredding of the wires. I did this for both heat sinks. The wires go up to the top and straight to the driver. I did this on the back for the power cords, too.



I don't have pics of my first power-up as that was when I had my first round of fervent cursing. I had wired one heat sink's cool whites to the other heat sink's neutral whites. D'oh! There goes my nice and neat color coding for my lights. the solution I chose was much more time and patience friendly. I just switched a few connections, and presto!



And with the neutral whites added in:



Here's a look at how the drivers, fans, and controllers are set up. The fan on the left is without a housing, temporarily. It was forgotten in packaging



A shot down the long edge so you can see how the wiring is hidden, as well as the end caps for the heat sink. The DIM4 is fastened to a 1/4" sheet of acrylic, and slid into the gap above the heat sink fins. I didn't enclose it as it needs to be cooled as well. I might figure something out for that though. For now, it's accessible and safe from water.



A shot of the emitters and wacky wiring:




A final shot from the front, with sleepy puppy:



I would absolutely buy this kit again. It is super versatile and made assembly mostly painless. Best of all, it looks great - I can't wait to see it over my tank! I just need to wait on an A/C adapter for the DIM4 (the one I have is a little short on current to support all my gadgets at once), and the fan housing from LED Group Buy.
theblondskeleton is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 07-20-2012, 05:36 PM   #2
fplata
Planted Tank Enthusiast
 
fplata's Avatar
 
PTrader: (18/100%)
Join Date: May 2012
Location: Miami, FL, United States
Posts: 948
Default

where did you get all of the parts, this looks awesome
fplata is offline   Reply With Quote
Old 07-20-2012, 06:30 PM   #3
xenxes
Planted Tank Guru
 
xenxes's Avatar
 
PTrader: (37/100%)
Join Date: Dec 2011
Location: Miami, FL
Posts: 2,669
Default

Very cool, how much did all that cost you?
xenxes is offline   Reply With Quote
Old 07-20-2012, 06:59 PM   #4
sunyang730
Wannabe Guru
 
sunyang730's Avatar
 
PTrader: (32/100%)
Join Date: Jan 2012
Location: New York, NY
Posts: 1,176
Default

You got a scary cat over there with nice LED eyes. LOL
__________________


Please forgive me for my grammar mistakes!
sunyang730 is offline   Reply With Quote
Old 07-20-2012, 07:36 PM   #5
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Quote:
Originally Posted by fplata View Post
where did you get all of the parts, this looks awesome
Thank, im pretty happy with it! I got pretty much everything from LED Group Buy. They are a sponsor here on the forum. It's pretty much one-stop shopping The aluminum spacers, extruded u-channel, and random nuts and bolts I got at Home Depot.

Off topic, if you don't have a multimeter, get one - it's very helpful when trouble shooting

Quote:
Originally Posted by xenxes View Post
Very cool, how much did all that cost you?
Well, I got free shipping for ordering on the 4th of July, but total around $500 including the controller. If I had built my own drivers, it would have been considerably cheaper. I also could have gone with cheaper LEDs, but the XT-E's are only about $4 apiece with comparable performance to an XP-G. I expect a huge difference in my electric bill. Soon enough, this fixture will pay for itself!

Quote:
Originally Posted by sunyang730 View Post
You got a scary cat over there with nice LED eyes. LOL
Wow, I hadn't noticed that! Ha! She looks like a Cylon to me....

I just finished hanging this a minute ago. The difference is astounding! The shadows are sharper enhancing the texture of my rocks, the shimmer is pretty but not overwhelming, and there is only a small sliver of the tank that is in the dimmer portion of the beam. This is lower light than I had with the T5HO's (or at least it appears to be so) so I will see some slower growth, but that's what I was aiming for. Still, I'm seeing pearling almost immediately.

I will have to report back on the DIM4 controller, however. I have a suspicion that it will not dim as effectively as I want. We'll see!
theblondskeleton is offline   Reply With Quote
Old 07-20-2012, 08:25 PM   #6
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

According to Hoppy's LED Calculator I have approximately 52 PAR at my substrate and 75 PAR at mid-tank. At upgrade time, I'll likely go with a 1100 mA driver and raise the fixture to get more even coverage and have more flexibility if I want higher light later. For now, this will do very nicely
theblondskeleton is offline   Reply With Quote
Old 07-21-2012, 07:08 PM   #7
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Installed My only complaint is that the hanging bar is pretty high. I may shorten the wires and lower the bar so that the fixture is closer to the bar and it doesn't look as funny. I did reinstall the hanging bars so that the bars are on the sides of the aquarium. This way they are not visible when viewing the aquascape:



Pardon the crummy iPhone pics

Last edited by theblondskeleton; 07-21-2012 at 07:10 PM.. Reason: Premature submission.
theblondskeleton is offline   Reply With Quote
Old 07-21-2012, 09:26 PM   #8
Algae Beater
Planted Tank Obsessed
 
Algae Beater's Avatar
 
PTrader: (0/0%)
Join Date: Jun 2011
Location: Vancouver, Canada
Posts: 352
Default

usually im not a fan of most DIY LED lighting systems (girlfriend dislikes ugly things ) , but this one looks as well as it performs! good show!
Algae Beater is offline   Reply With Quote
Old 07-23-2012, 07:11 AM   #9
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Quote:
Originally Posted by Algae Beater View Post
usually im not a fan of most DIY LED lighting systems (girlfriend dislikes ugly things ) , but this one looks as well as it performs! good show!
Thanks! My wife was a little concerned at first, but she loves it almost as much as I do. Admittedly, she is mostly impressed that I put it together without burning the house down, haha...

I got my new ac adapter yesterday, so I'll be installing that and the fan housing tomorrow.
theblondskeleton is offline   Reply With Quote
Old 08-27-2012, 05:39 AM   #10
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Update time! I reinstalled the hanging wires at a shorter distance, and raised the fixture a few inches. I also reduced the current a bit. It seems I was getting much more light from this than I originally calculated. It has warmed up quite nicely. Even at the greater height, there is very little glare with the optics installed. It makes it very pleasant to view my aquarium. Absolutely loving this, and so are my plants. No trouble getting color from my Rotala, and everything looks super healthy!

Btw, six bridgelux blues are too much for moonlights. I have to keep them cranked WAY down. Almost no use at this level. Might replace them with some warm whites to bring out the reds and oranges a bit.
theblondskeleton is offline   Reply With Quote
Old 08-27-2012, 02:52 PM   #11
wastedtime
Planted Tank Obsessed
 
wastedtime's Avatar
 
PTrader: (23/100%)
Join Date: Oct 2011
Location: Massachusetts
Posts: 452
Default

Looking good, How are you hanging the lights ? I checked and didnt see any hanging kits for the Makers LED Heatsink.
wastedtime is offline   Reply With Quote
Old 08-28-2012, 05:29 AM   #12
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Thanks! I installed several eyebolts across the aluminum u-channel - 4 for each fixture. There is a 3/8" (approx) bolt channel at the top of the heat sink you can use as well. I attached stainless steel braided wire (picture hanging wire rated for 50lbs) with ferrules across each pair of eyebolts. Instead of using the stops, I just crimped the ferrules. It's just slung over the hanging pipe at about 4". Looks super clean, even with the power cables. I'll post a pic when I get a chance.
theblondskeleton is offline   Reply With Quote
Old 08-28-2012, 05:35 AM   #13
IWANNAGOFAST
I see LEDs
 
IWANNAGOFAST's Avatar
 
PTrader: (33/100%)
Join Date: Jan 2008
Location: San Francisco
Posts: 1,864
Default

Your thread inspired me to try out this kit on my next tank. Very excited for it all to come in!
IWANNAGOFAST is offline   Reply With Quote
Old 08-28-2012, 05:38 AM   #14
theblondskeleton
Planted Tank Enthusiast
 
theblondskeleton's Avatar
 
PTrader: (13/100%)
Join Date: Aug 2009
Location: Vancouver, WA, USA
Posts: 537
Default

Excellent! You won't be disappointed. I think it's very well thought out and it looks great. The ability to change things if I don't like them and upgrade in the future is priceless, in my opinion have fun!
theblondskeleton is offline   Reply With Quote
Old 08-28-2012, 08:25 AM   #15
Algae Beater
Planted Tank Obsessed
 
Algae Beater's Avatar
 
PTrader: (0/0%)
Join Date: Jun 2011
Location: Vancouver, Canada
Posts: 352
Default

the warm whites are quite good at bring out reds! i have XP-G warm whites in one of my lighting systems and they really make the red plants pop! and have the bonus of having the highest CRI of any LED
Algae Beater is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 01:13 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012