CO2 Paintball Tank CGA 320 Adapter
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment


Reply
 
Thread Tools Display Modes
Old 12-09-2012, 07:37 PM   #1
tbullet
Algae Grower
 
PTrader: (0/0%)
Join Date: Nov 2012
Location: Just around the corner
Posts: 23
Default CO2 Paintball Tank CGA 320 Adapter

anyone used this with success on a paint ball tank?

http://www.amazon.com/AQUATEK-CO2-Pa.../dp/B004M49QDC

I'm looking to purchase one. That way I can use my dual stage regulator. this is what I'm looking to do.

Suggestions?
Attached Images
 
__________________

Later;
I'm way deep into nothing special.
tbullet is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 07:39 PM   #2
kevmo911
Planted Tank Guru
 
kevmo911's Avatar
 
PTrader: (32/100%)
Join Date: Sep 2010
Location: Greensboro, NC
Posts: 3,895
Default

Yeah they work fine. Unless you anchor the tank well, you'll have to pull off an amazing balancing trick with the dual to keep the pb can upright
kevmo911 is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 07:44 PM   #3
tbullet
Algae Grower
 
PTrader: (0/0%)
Join Date: Nov 2012
Location: Just around the corner
Posts: 23
Default

I'll secure the tank. that isn't hard to do. Now, to open the valve to let the CO2 out, that's the small screw on the side of the tank at the top right? I know the pin needs to be pushed on the valve in to release the co2. but how will I be able to connect the reg and adapter with out the co2 coming out?
__________________

Later;
I'm way deep into nothing special.
tbullet is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 08:01 PM   #4
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Toronto
Posts: 8,730
Default

Quote:
Originally Posted by tbullet View Post
I'll secure the tank. that isn't hard to do. Now, to open the valve to let the CO2 out, that's the small screw on the side of the tank at the top right? I know the pin needs to be pushed on the valve in to release the co2. but how will I be able to connect the reg and adapter with out the co2 coming out?
Yes, I believe the screw is an on/off valve.
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is offline   Reply With Quote Quick reply to this message
Old 12-10-2012, 05:01 PM   #5
hbosman
Wannabe Guru
 
hbosman's Avatar
 
PTrader: (1/100%)
Join Date: Oct 2006
Location: Leesburg Virginia
Posts: 1,594
Default

Quote:
Originally Posted by kevmo911 View Post
Yeah they work fine. Unless you anchor the tank well, you'll have to pull off an amazing balancing trick with the dual to keep the pb can upright
yeah, I sure lucked out with a Vicker Dual Stage. It balanced perfectly.

http://www.flickr.com/photos/h_bosman/4379697140/
hbosman is offline   Reply With Quote Quick reply to this message
Old 12-10-2012, 05:19 PM   #6
nokturnalkid
Wannabe Guru
 
nokturnalkid's Avatar
 
PTrader: (81/100%)
Join Date: Apr 2007
Location: HI, but Pueblo, CO for now
Posts: 1,233
Default

Quote:
Originally Posted by hbosman View Post
yeah, I sure lucked out with a Vicker Dual Stage. It balanced perfectly.

http://www.flickr.com/photos/h_bosman/4379697140/
I got a matheson dsr on a 20 oz paintball with the aquatek adapter and it balanced perfectly too, still strapped it down though. One thing to watch, make surethe o-ring is seated perfectly on the tank. If it isn't, the adapter/reg will shred the oring and your co2 will come out untill you unscrew.
__________________
Schuber Wright 6 gal
Mr. Aqua 11.4 g...coming soon
30gal Journal - RIP
nokturnalkid is online now   Reply With Quote Quick reply to this message
Old 12-10-2012, 06:02 PM   #7
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Toronto
Posts: 8,730
Default

Quote:
Originally Posted by hbosman View Post
yeah, I sure lucked out with a Vicker [sic] Dual Stage. It balanced perfectly.

http://www.flickr.com/photos/h_bosman/4379697140/
I would strap that down
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 07:51 PM   #8
kevmo911
Planted Tank Guru
 
kevmo911's Avatar
 
PTrader: (32/100%)
Join Date: Sep 2010
Location: Greensboro, NC
Posts: 3,895
Default

nonononono...

Don't mess with the safety valve (that's the screw) on the pb cylinder.

Attach the adapter securely to the reg, then screw the whole thing onto the pb cylinder. It will hiss briefly as you tighten it down. Just make sure your solenoid is off and your working pressure is at zero when you attach it. For as long as the adapter is attached to the pb cylinder, the cylinder will be "open". That depressed pin is the equivalent of the on/off valve at the top of a standard industrial cylinder.

I'd still recommend a 5, 10, or 20# cylinder over a pb cylinder any day, but I assume you have a reason for it.
kevmo911 is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 08:23 PM   #9
treckel
Algae Grower
 
PTrader: (0/0%)
Join Date: Oct 2012
Location: Minnesota
Posts: 29
Default

The screw is NOT an on/off valve.

Sent from my SCH-I535 using Tapatalk 2
treckel is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 08:27 PM   #10
tbullet
Algae Grower
 
PTrader: (0/0%)
Join Date: Nov 2012
Location: Just around the corner
Posts: 23
Default

ok so add the adapter first then the reg? or attach the adapter to the reg and then to the tank.

Which way?

Thanks.
__________________

Later;
I'm way deep into nothing special.
tbullet is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 08:43 PM   #11
oldpunk78
ಠ_ಠ
 
oldpunk78's Avatar
 
PTrader: (104/100%)
Join Date: Nov 2008
Location: 96007
Posts: 5,025
Default

Quote:
Originally Posted by tbullet View Post
ok so add the adapter first then the reg? or attach the adapter to the reg and then to the tank.

Which way?

Thanks.
OP's forgot to answer you question

If you do use one of those adapters, you connect the adapter the regulator first. Make sure you use the washer between the two. Make it as tight as you can without damaging anything. Then connect the whole thing to the paintball tank.
oldpunk78 is online now   Reply With Quote Quick reply to this message
Old 12-10-2012, 12:23 AM   #12
Darkblade48
Moderator
 
Darkblade48's Avatar
 
PTrader: (3/100%)
Join Date: Jan 2008
Location: Toronto
Posts: 8,730
Default

Quote:
Originally Posted by treckel View Post
The screw is NOT an on/off valve.

Sent from my SCH-I535 using Tapatalk 2
My apologies, I thought it was something like this:



Quote:
Originally Posted by tbullet View Post
ok so add the adapter first then the reg? or attach the adapter to the reg and then to the tank.

Which way?

Thanks.
Quote:
Originally Posted by oldpunk78 View Post
OP's forgot to answer you question

If you do use one of those adapters, you connect the adapter the regulator first. Make sure you use the washer between the two. Make it as tight as you can without damaging anything. Then connect the whole thing to the paintball tank.
As oldpunk78 mentioned, the easiest way is to add the adapter to the regulator first, and then screw the whole thing into the paintball cylinder.

I would imagine some CO2 loss is inevitable, however. Just screw it on quickly, perhaps?
__________________
Anthony

A Primer to Pressurized CO2 and A Primer to Planted Tanks
Eheim Pimp #362 - Eheim 2213 x2, Eheim 2028, Eheim 2217, Eheim surface skimmer and Eheim autofeeder.
Victor Pimp #33 - HPT272-125-350-4M
Darkblade48 is offline   Reply With Quote Quick reply to this message
Old 12-09-2012, 08:32 PM   #13
oldpunk78
ಠ_ಠ
 
oldpunk78's Avatar
 
PTrader: (104/100%)
Join Date: Nov 2008
Location: 96007
Posts: 5,025
Default

I don't know why people mess around with an adapter when they are just going to build their own reg to use with a paintball tank. They do make 1/4 NPT to paintball tank fittings.

Check it out:





It just seems like I've read so many folks having issues with those cga-320 to paintball adapters. (operator error...) With this, you just screw the paintball tank directly to your reg.

(please forgive my beat-up hands)

Last edited by oldpunk78; 12-09-2012 at 08:33 PM.. Reason: typo
oldpunk78 is online now   Reply With Quote Quick reply to this message
Old 12-10-2012, 01:08 AM   #14
FlyingHellFish
Wannabe Guru
 
FlyingHellFish's Avatar
 
PTrader: (0/0%)
Join Date: Nov 2011
Location: Canada
Posts: 1,668
Default

Quote:
Originally Posted by oldpunk78 View Post
I don't know why people mess around with an adapter when they are just going to build their own reg to use with a paintball tank. They do make 1/4 NPT to paintball tank fittings.

Check it out:





It just seems like I've read so many folks having issues with those cga-320 to paintball adapters. (operator error...) With this, you just screw the paintball tank directly to your reg.

(please forgive my beat-up hands)
Wait, so you can just buy these adapter and install them to an 1/4 port on your regulator?

Any advantages or disadvantages over a CGA320? I google that and they call it an ASA fitting?
FlyingHellFish is offline   Reply With Quote Quick reply to this message
Old 12-10-2012, 01:15 AM   #15
oldpunk78
ಠ_ಠ
 
oldpunk78's Avatar
 
PTrader: (104/100%)
Join Date: Nov 2008
Location: 96007
Posts: 5,025
Default

Quote:
Originally Posted by FlyingHellFish View Post
Wait, so you can just buy these adapter and install them to an 1/4 port on your regulator?
Yep.
Quote:
Any advantages or disadvantages over a CGA320? I google that and they call it an ASA fitting?
Sure. There's always some kind of trade off...

Advantage - You just buy one fitting. It's simpler.

Disadvantage - Can't hook up to a standard a standard CGA-320 cylinder. (without the reverse adapter) This part needs a strap wrench for the install.
oldpunk78 is online now   Reply With Quote Quick reply to this message
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 04:52 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012