The Planted Tank Forum - View Single Post - Calling all DIY LED "Junkies" - Your opinions wanted!
View Single Post
Old 01-16-2013, 10:02 PM   #152
O2surplus
Planted Tank Enthusiast
 
O2surplus's Avatar
 
PTrader: (4/100%)
Join Date: Jan 2010
Location: yorba linda, ca.
Posts: 577
Default

Quote:
Originally Posted by skanderson View Post
ok i pasted it into my ardino oo23. when i try to verify or upload i get the following message/*
Code:
// ATMEG328P-AU Microcontroller LED lighting controller for aquarium use. 
// The programming code uses a DS1307 Real Time clock to set the LED lighting schedule. Current date and time can be accessed with the serial monitor set to 9600 baud.
// sunrise/sunset time,length of fade duration, and the length of the day are selectable via the programmed schedule.  
//  Circuit description
// PWM pins described below connected to dimming circuits on drivers spread among 6 seperate channels.
// DS1307 RTC ( real time clock) connected via I2C protocol.
*/



// Pins to control each channel LEDs. Change these if you're using different pins.

int oneLed = 3;       // LED PWM arduino pin for channel one.

int twoLed = 5;       // LED PWM arduino pin for channel two 

int threeLed = 6;     // LED PWM arduino pin for channel three

int fourLed = 9;      // LED PWM arduino pin for channel four

int fiveLed = 10;     // LED PWM arduino pin for channel five

int sixLed = 11;      // LED PWM arduino pin for channel six


#include <WProgram.h>
#include <DS1307.h> 
// written by  mattt on the Arduino forum and modified by D. Sjunnesson



// Set up RTC

#include "Wire.h"

#define DS1307_I2C_ADDRESS 0x68



// RTC variables

byte second, rtcMins, oldMins, rtcHrs, oldHrs, dayOfWeek, dayOfMonth, month, year;



// Other variables. These control the behavior of lighting. Change these to customize behavior.

int minCounter = 0;         // counter that resets at midnight. Don't change this.



int oneStartMins = 540;     // minute to start channel 1. Change this to the number of minutes past midnight you want to start

int twoStartMins =420;      // minute to start channel 2. Change this to the number of minutes past midnight you want to start                         

int threeStartMins =540;    // minute to start channel 3. Change this to the number of minutes past midnight you want to start 

int fourStartMins =420;     // minute to start channel 4. Change this to the number of minutes past midnight you want to start 

int fiveStartMins =420;     // minute to start channel 5. Change this to the number of minutes past midnight you want to start 

int sixStartMins =420;      // minute to start channel 6. Change this to the number of minutes past midnight you want to start 


int onePhotoPeriod = 720;   // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day

int twoPhotoPeriod = 960;   // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day                           

int threePhotoPeriod = 720; // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day

int fourPhotoPeriod = 960;  // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day

int fivePhotoPeriod = 960;  // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day

int sixPhotoPeriod = 960;   // photoperiod in minutes, for this channel. Change this to alter the total legnth of the day


int fadeDuration = 180;      // duration of the fade on and off for sunrise and sunset. Change
                            
//    this to alter how long the fade lasts.

int oneMax = 255;           // max intensity for this channel. Change if you want to limit max intensity.

int twoMax = 255;           // max intensity for this channel. Change if you want to limit max intensity. 

int threeMax = 255;         // max intensity for this channel. Change if you want to limit max intensity.

int fourMax = 255;          // max intensity for this channel. Change if you want to limit max intensity.

int fiveMax = 255;          // max intensity for this channel. Change if you want to limit max intensity.

int sixMax = 255;           // max intensity for this channel. Change if you want to limit max intensity.

/****** LED Functions ******/

/***************************/

//function to set LED brightness according to time of day

//function has three equal phases - ramp up, hold, and ramp down

void setLed(int mins,    // current time in minutes
            
int ledPin,  // pin for this channel of LEDs
            
int start,   // start time for this channel of LEDs
            
int period,  // photoperiod for this channel of LEDs
            
int fade,    // fade duration for this channel of LEDs
            
int ledMax   // max value for this channel
            
)  {
  
if (mins <= start || mins <= mins > start + period)  {
    
analogWrite(ledPin, 0);
  
}// This is when the led's are off, thus ledVal =0
  
if (mins > start && mins <= start + fade)  {
    
analogWrite(ledPin, map(mins - start, 0, fade, 0, ledMax));
  
}// This is sunrise. Leds slowly brighten to full intensity
    
if (mins > start + fade && mins <= start + period - fade)  {
   
analogWrite(ledPin, ledMax);
  
}//This is when the led's are at maximum intensity
    
if (mins > start + period - fade && mins <= start + period)  {
    
analogWrite(ledPin, map(mins - start - period + fade, 0, fade, ledMax, 0));
  
}// This is sunset. LEDs slowly fade out.

}



/***** RTC Functions *******/

/***************************/

// Convert normal decimal numbers to binary coded decimal

byte decToBcd(byte val)

{
  
return ( (val/10*16) + (val%10) );

}



// Convert binary coded decimal to normal decimal numbers

byte bcdToDec(byte val)

{
  
return ( (val/16*10) + (val%16) );

}



// 1) Sets the date and time on the ds1307

// 2) Starts the clock

// 3) Sets hour mode to 24 hour clock

// Assumes you're passing in valid numbers.



/* //remove the forward slash and asterisk at the far left to activate the time date setting code




void setDateDs1307(byte second, // 0-59 
                   
byte minute, // 0-59
                   
byte hour, // 1-23
                   
byte dayOfWeek, // 1-7
              
byte dayOfMonth, // 1-28/29/30/31
                   
byte month, // 1-12
                   
byte year) // 0-99

{
   
Wire.beginTransmission(DS1307_I2C_ADDRESS);
   
Wire.send(0);
   
Wire.send(decToBcd(second));
   
Wire.send(decToBcd(minute));
   
Wire.send(decToBcd(hour));
   Wire.send(decToBcd(dayOfWeek));
   
Wire.send(decToBcd(dayOfMonth));
   
Wire.send(decToBcd(month));
   
Wire.send(decToBcd(year));
   
Wire.endTransmission();
     
                             

}

*/ //remove the forward slash and asterisk at the far left to activate the time date setting code



// Gets the date and time from the ds1307 via the I2C protocol.

void getDateDs1307(byte *second,
          
byte *minute,
          
byte *hour,
          
byte *dayOfWeek,
          
byte *dayOfMonth,
          
byte *month,
          
byte *year)

{
  
Wire.beginTransmission(DS1307_I2C_ADDRESS);
  
Wire.send(0);
  
Wire.endTransmission();

  

Wire.requestFrom(DS1307_I2C_ADDRESS, 7);

  
*second     = bcdToDec(Wire.receive() & 0x7f);
  
*minute     = bcdToDec(Wire.receive());
  
*hour       = bcdToDec(Wire.receive() & 0x3f);
  
*dayOfWeek  = bcdToDec(Wire.receive());
  
*dayOfMonth = bcdToDec(Wire.receive());
  
*month      = bcdToDec(Wire.receive());
  
*year  = bcdToDec(Wire.receive());

}



void setup()  { 
    


// init I2C  
  
Serial.begin(9600);
  
Wire.begin();
} 
// these functions only occur once.



/***** Main Loop ***********/

/***************************/

void loop() { 

 
 
  

// get time from RTC and put in hrs and mins variables
  
getDateDs1307(&second, &rtcMins, &rtcHrs, &dayOfWeek, &dayOfMonth, &month, &year);
  
minCounter = rtcHrs * 60 + rtcMins;
 
Serial.print(RTC.get(DS1307_HR,true)); //read the hour and also update all the values by pushing in true
  
Serial.print(":");
  
Serial.print(RTC.get(DS1307_MIN,false));//read minutes without update (false)
  
Serial.print(":");
  
Serial.print(RTC.get(DS1307_SEC,false));//read seconds
  
Serial.print("      "); // some space for a more happy life
  
Serial.print(RTC.get(DS1307_MTH,false));//read month
  
Serial.print("/");
  
Serial.print(RTC.get(DS1307_DATE,false));//read date
  
Serial.print("/");
  
Serial.print(RTC.get(DS1307_YR,false)); //read year 
  
Serial.println();


//set LED values
  
setLed(minCounter, oneLed, oneStartMins, onePhotoPeriod, fadeDuration, oneMax);
  
setLed(minCounter, twoLed, twoStartMins, twoPhotoPeriod, fadeDuration, twoMax);
  
setLed(minCounter, threeLed, threeStartMins, threePhotoPeriod, fadeDuration, threeMax);
  
setLed(minCounter, fourLed, fourStartMins, fourPhotoPeriod, fadeDuration, fourMax);
 
setLed(minCounter, fiveLed, fiveStartMins, fivePhotoPeriod, fadeDuration, fiveMax);
   
setLed(minCounter, sixLed, sixStartMins, sixPhotoPeriod, fadeDuration, sixMax);
 
// Get ready for next iteration of loop
  
delay(1000);
all that is in red under a message that says RTC was not declared in this scope . what am i doing wrong? thanks again for the help.
You probably don't have the needed "DS1307" Library installed in your arduino's library folder. Here's the library- just place the unzipped folder into your "library" folder and try again.
Attached Files
File Type: zip DS1307.zip (94.8 KB, 36 views)
__________________
225 Gal, Glass "Reef Ready" w/ twin Iwaki Pumps & 2 Ocean Clear inline filters. Custom 320 watt LED Lighting system utilizing a 6' Maker's Heat Sink, 12 BridgeLux Vero 18's,3 purpose built 5 channel A6211 Led driver/Controllers, and a 20lb CO2 system w/ Milwaukee Ph Controller.
O2surplus is online now   Reply With Quote