The Planted Tank Forum - Reply to Topic
Thread: Good looking overflow siphon attempt Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
07-01-2013 03:59 AM
plantbrain Old Krib link shows a different idea:
07-01-2013 03:57 AM
plantbrain This same design has been around for decades BTW, PVC pipe was used for many a DIY breeder tank I've seen.

Google search DIY PVC overflow skimmer:
07-01-2013 03:11 AM
Kathyy Very nice!
06-30-2013 09:16 PM
Jahn makes for a killer protein skimmer too, haha! nice!
06-30-2013 08:58 PM
Rudger I updated the first post with the latest version of my overflow.
05-28-2013 10:17 PM
Rudger I depending how busy I am with work, I might be able to build a better version within the week. I'll keep this thread updated.

As for the picture in my car. I have some driveway moments when I want to finish listening to a radio broadcast. I'll usually fiddle with something at the same time.
05-28-2013 09:58 PM
lochaber pretty impressive work, looks good.

let us know how it works out, or if you make any changes.
05-28-2013 12:10 AM
thelub Do you usually do aquarium work in your car? Lol

I'm having a hard time understanding how this will work so I'm looking forward to pictures of it up and running on your aquarium.
05-27-2013 10:57 PM
Good looking overflow siphon attempt

I have updated my overflow siphon. Here is what it looks like now:

It looks better in the water:

I decided to do away with a self priming venturi because it would spray bubbles into the tank every few seconds. It has run several days without any bubble accumulation, but i must admit I've only tested flow ranging from 100-150gph for extended periods.
I made the intake height and tank hook height adjustable with a nylon set screw. This lets me tweak the water level without excessive air being sucked down.

Here is my biggest change:

I took a lesson from dual stand pipes to completely eliminate the "glug glug" or toilet flush noise. I just close down the gate valve until the lower pipe no longer sucks any air.
You can hear how quiet it is here:
The trickle you hear is just the water falling about an inch down the pipe inside.

I am pretty happy with my results now and am going to look into putting it on a tank. I wish I could have made it a little more compact and keep the same flow capacity, but this is as tight as I could manage to push the bend radius of acrylic without creasing.

Here is the old post:
I don't even have a tank with a sump, but for some reason I became fixated with trying to make an overflow siphon that would look presentable in a rimless tank. Here is my DIY Mame overflow ripoff attempt:

And here it is in action

I will do some more fiddling, because right now I need to pump about 100gph for the venturi to self-prime the siphon but the it maxes out at about 150gph. I would not trust such a small window of flow to not dump water all over my floor. I also need to cut down on some of that noise on the siphon break.

Here's how I made it:
I started with 1" acrylic tubing. To keep it from collapsing while bending I stuffed it with 3/4" silicon tubing. I then filled the tubing with sand to make it a little more rigid.

From there I would heat the tubing with a heat gun and carefully bend it. The tightest bend radius I could manage without the pipe getting creases was about 2.5" on center.

And here is is with all the main bends done:

I untied the end of the silicon tube and dumped out all the sand so I could pull it out. Well that is what I was hoping anyway. The tubing would not budge until I worked some mineral oil in there.

Here we go, finally got it out:

From here I started to drill a hole in the top of the loop for a siphon break. Of course, cracks started to form. In an attempt to salvage all the time I spent bending the tube, I heated up the pilot hole and stretched it out enough to fit 1/2" acrylic tubing. I glued the tubing in place with some number 4 cement, then reinforced it with a little bead of number 16 cement.

I had originally planned to have some airline feed through this half inch pipe up to the top of the siphon for priming like this:

But air bubbles liked sticking around just downstream of the opening of the tube, so I decided to feed it in the intake side.

On the intake side I had a problem with air getting dragged down the pipe. I found flaring the end like a blunderbuss helped with that.

From here I plan to work on:
a more elegant implementation of the priming tube
less return flow required to self prime
a better placement for the siphon break
tighter pipe bend radius or less deformation on the bend

I would appreciate any input on the design or advice on making acrylic bend to my will.

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome