The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY > How to DIY Divide/Split fish tank?

Thread: How to DIY Divide/Split fish tank? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-16-2013 01:59 AM
xavinovic I wonder if the aluminum will cause any problem?
06-15-2013 11:25 PM
xavinovic

This is what I came up with. I'm trying to see what I close the top with so the shrimp don't clim over.
06-15-2013 01:15 AM
fish_22 I was just thinking about how to do this in one of my tanks earlier, as I need to separate 2 bettas but still have them in one tank. I was thinking that maybe I could get a small drill bit (as small as you need to keep the fish from getting through) and drill holes about every 3"-5". I dont know if that would work, but maybe...
06-15-2013 12:16 AM
Raaan I can see where you're coming from. I was trying to think of the least "intrusive" way of doing it (without having to use adhesive or drill extra holes). I've used this method on very small holes in plastic cups within a tank, but if they were much larger I imagine it would be pretty easy to knock them out by accident.

I agree with stealthypotatoes method in that case, using a fine mesh and small drill holes would be best. Unless you were to try getting really tricky with a router.
06-14-2013 09:20 PM
stealthypotatoes I would cut a vent in the bottom and then drill holes around that vent and then cut a piece of ss mesh and just stitch it up with some nylon or fishing thread
You could also do this on the top so that there wont be any oils left behind
06-14-2013 04:16 AM
Sluggo Why not use some vinyl window screen?
06-13-2013 05:23 PM
xavinovic I found a plastic light diffuse that might work. Now I'm trying to figure out how would I get the SS wire mesh to stick on the light diffuser.
06-13-2013 05:18 PM
xavinovic Raaan- I totally understand your theory but I'm looking for something more sustainable because if the sponge comes off for some reason they will all get mixed. Thank you.
06-13-2013 05:15 AM
Dr Fishbait You could go to to Swisstropicals.com or Angelsplus.com to buy 2 inch foam as a tank divider. They make it for many tank sizes. It'll also act as additional filtration. I bought some to divide my new 40 breeder to breed rams and hopefully Kribs.
06-13-2013 04:13 AM
Diana There is a craft mesh that is available in Michaels and similar stores. It needs a frame, but will allow a lot of water movement between the halves. Such as filter intake on one side and outlet on the other.
06-13-2013 04:08 AM
Raaan I would use a piece of filter sponge instead. Get one precut into a cylinder or cut a circular piece about 1/2" thick and with a larger diameter than the hole you're filling, then cut a groove along the outer edge so that you can wedge it into the hole.

Not sure if that translated from my mind well enough to be useful. Haha.
06-13-2013 03:02 AM
xavinovic
How to DIY Divide/Split fish tank?

I'm trying to Divide/Split a fish tank. I have a few ideas.

I went to home depo and they have some plexiglass that I could use it to split the tank in half but I want to make a hole in the middle so water flows to both sides and cover it with really fine SS mesh that I already have.

The question is how would I glue or keep the SS mesh cover the hole?

Should I buy 2 plexiglass make the hole in both and glue them together? What can I glue them with so it looks right.

Has any one done this?

I'm trying to keep BKK and Red Rubys separate.

Thanks for any feed back.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 08:11 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012