|Topic Review (Newest First)|
|03-25-2013 04:59 PM|
Originally Posted by thelub View Post
I'm excited to break some sh!t.
|03-25-2013 05:43 AM|
Use it for the bottom of an aquarium. 55x30 would be a really nice deep tank. Or there might be a DIYer out there looking for a cheap foundation for their tank. I'd think about taking it off your hands if I was anywhere near your neighborhood.
Or break it which is lots of fun too
|03-25-2013 04:53 AM|
Originally Posted by Hoppy View Post
I think the people that put it out were hoping someone would pick it up 'cause I don't think the garbage truck would take it away so easily... Mine around here are pretty strict with lengths and weights. This piece of glass probably exceeds both limits.
|03-25-2013 04:10 AM|
Originally Posted by ajmckay View Post
|03-25-2013 03:33 AM|
Using a few methods I was able to determine for sure that the glass is in-fact tempered.
I'm soo bummed...
|03-24-2013 01:10 AM|
|xmas_one||Do a plywood tank with the 36" piece.|
|03-24-2013 12:46 AM|
|TheDrake||try this to see if it's tempered|
|03-23-2013 02:43 PM|
|genocdex||im saying to use the holes. cut off the right most 2, they are too close to the end. but then the remaining 2 you can work into the tank for a canister filter intake and output. kinda like how many people like to do sw tanks. just have to make them a bit bigger (maybe) and buy the bulk head plumbing...|
|03-23-2013 03:18 AM|
|ajmckay||Hmm... I'm not getting 18x15 to fit (without using the scored piece or using the holes)|
|03-22-2013 09:27 PM|
you could do a 18x18x15" using 2 holes as a sump style of filter or just the in and out for a canister filter.....
they might be too small, might need to increase them a bit. but a that should be at least 25g tank for you, using the 1/2 for bottom....
|03-22-2013 08:57 PM|
Nice find! Free glass is always nice
I don't think it is possible to cut tempered glass at all. They temper it once its the size that is needed. It is hard to find float glass any more. Most glass that is used in homes is tempered because it is a lot less dangerous than float.
If you have some polarized glasses, look at the back window of a car and compare it to the glass. If they look the same its tempered.
If its not tempered, the score mark will prove difficult to cut if your new cut line intersects that one. Most of the time glass will break on an existing score line.
If it is tempered, you have yourself a new bottom for a 55x30 tank
|03-22-2013 08:49 PM|
Originally Posted by lochaber View Post
Also good point about it possibly being tempered. If it were a shower door I'm sure it would be tempered, right? I'll check with some polarized lenses to see if it's tempered...
If it is tempered I can cut it with a diamond wet saw, correct? I have one of those I use to cut ceramic tile.
As for uses, I think a 14" cube would be pretty cool. I've never had a cube but I've always wanted one. So far I've figured out how to cut the glass such that 3 pieces would have a polished & beveled top edge. I'll see if I can work in a 4th, but I'm thinking I may have to polish that edge up myself. How cool would it be to have a 14" cube for free
|03-22-2013 05:23 AM|
I'm guessing it might have used to be a shower door?
before you even think about cutting it, try to figure out if it's tempered. Easiest (but least likely to provide any info) would be to look over it for any etchings/markings stating it's tempered.
Failing that, I'd look along the edges for that characteristic conchoidal fracturing. Finding some wouldn't necessarily mean it's not tempered, but it would be some evidence towards that.
There is a way you can check for whether glass is tempered or not using polarized lenses (you can get these from the 3D glasses in movies). I'm not sure on the specifics for checking tempered, but play with the lenses alone first, then with a piece of non-tempered glass, and then your new piece. Stack the lenses on top of each other, and look through both of them, and rotate just one of the lenses while you do this. There should be a point where they are almost completely black, and then it should get brightest about ~90 degrees from that arrangement.
|03-22-2013 05:08 AM|
|Hoppy||It isn't enough glass to make a 40B, as far as I can see. The score mark and the holes greatly reduce your options, even if you use the piece of .5 inch glass for the bottom. You might get a 16 inch high, 32 inch long tank made, about a 40 gallon, but with odd dimensions. I didn't check to see if the glass thickness is enough for that size tank. I don't think it is.|
|03-22-2013 04:27 AM|
|assasin6547||Nice find! The other piece of glass is the size of the bottom of a 40b, you should make a 40 gallon breeder. Just cut out sides for the tank.|
|This thread has more than 15 replies. Click here to review the whole thread.|