The Planted Tank Forum - Reply to Topic
Thread: Aqueon Evolve woes... what should I do? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
03-11-2013 12:29 AM
Originally Posted by tiggity View Post
Get a hob with the intake on the right side and hang it on the back with the intake in the pump section
Yeah, I thought about just getting an HOB, but I have two clip-on LED lights on the back taking up a lot of room, so I don't think it would fit too well.
03-10-2013 11:56 PM
tiggity Get a hob with the intake on the right side and hang it on the back with the intake in the pump section
03-10-2013 11:41 PM
echoskybound Thank you for your suggestions! I'm not sure that I could fit a piece of acrylic down there, it's a bit of a tight spot, but I'll look into the toxicity of the two part epoxy.

I came up with a bit of a hacky solution today. I tied a ziplock bag around the pump intake (the pump intake is just some slots around the impeller), with a hose coming out of it going straight into the media compartment, like this:

I'm thinking it might be best if I just get a pump that has a hose going in and a hose going out. My solution is working better for now, but there's still water getting in through the bag, also I don't really like having the pump in a bag, I worry that the plastic might get caught in the impeller.

Does anybody know of a really small submersible pump that has a hose in and a hose out?
03-10-2013 04:30 PM
TwoTacoCombo Try "holdfast epoxy stick"
03-10-2013 03:41 PM
BrokeCurmudgeon You may want to try some epoxy formed into a small rope and forced between the bottom and back to stop the leak. Some two part epoxy will form and harden underwater. I don't know about toxicity though.
03-10-2013 03:17 PM
pwolfe would it be possible to slide a trimmed to size piece of acrylic down there? basically doubling the wall?
03-10-2013 07:43 AM
Aqueon Evolve woes... what should I do?

I recently set up an Aqueon Evolve 4 as a nano shrimp tank. I got it all planted and set up when I realized I have a big filtration problem. The Evolve has a "false back" that hides the filtration. The intake goes into a small compartment with the filtration media, then the water spills into another compartment with the pump.

Here's a diagram of how the water is supposed to flow. The green box highlights the media compartment where the water is drawn in:

Unfortunately, my unit seems to have a bit of a defect. There's a gap on the bottom of my false back that allows water underneath the false back, and straight into the pump. I didn't really know this would be an issue until I got the tank all set up, planted, and cycling. I noticed that there was no movement in the media compartment. The water is stagnant, and I don't see any water being sucked in through the intake holes (I can see little particles of dust floating in my water, but they're not moving towards the intake holes, which suggests there's no water being drawn there.)

Here's a diagram of what I think is happening. The false back is highlighted in red. The water is flowing under the gap and straight into the pump, bypassing the media entirely:

If I had realized this sooner, I would have sealed the gap, but now the tank is full and planted and I don't know what my options are. I was thinking I could layer some media underneath of the pump, but that still leaves the stagnant water in the media compartment, and wouldn't be very effective.

Any ideas about anything I can do, aside from breaking the whole tank down again and sealing the gap? I dropped a bag of bio media in the bottom compartment next to the pump, and I wrapped the pump in foam so that it doesn't choke on any debris, but I'm not sure what I can do other than that.

Thanks for reading! I'm really bummed out that I didn't realize this was an issue until too late, ugh!

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome