The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment > What sealent is good for DIY yeast co2 system?

Thread: What sealent is good for DIY yeast co2 system? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-26-2013 07:09 AM
mistahoo
Re: What sealent is good for DIY yeast co2 system?

Drill a hole in the top. Use a nylon fitting and screw it on. Then stick the tubing onto the nipple. Truly failproof compared to anything mentioned on here so far. No leaks and you can remove it if needed or just swap the caps.

Sent from my spaceship using Tapatalk 2.
02-26-2013 03:15 AM
reconmarui I used a combination of excessive amounts of jb weld water proof putty that hardens(had it lying around) and hot glue, in excessive amounts too, holding up well so far or at least I'm getting bubbles
02-26-2013 01:24 AM
kaaayd I have tried silicone and just a tight fitting tube. Both have failed for me. What I have done now (and has worked consistently for the ones I made for friends) is:

Use a Gatorade bottle. I found that soda bottles tend to leak through the cap sometimes. It caused me hours of frustration until I used a Gatorade bottle (I use the bottles that are close to 2 liters and also the one that's a gallon or something). Seals perfect every time.

Drill the hole in the cap, put the tube through, then wrap some duct tape around the cap. Make sure there is a decent amount of tape above the cap. Fill it with Gorilla Glue (doesn't have to be to the top, but thick enough). Let it dry over night.

This will definitely work. I have never had a problem with this method.
02-26-2013 01:01 AM
thesawguy I will agree with the m00se method. But will add that with the tubing I used it eventually got stiff and leaked at the part that was squeezed, so I would just pull it down a little further and create a new squeeze point. Silicone and super glue failed for me after a few months.
02-26-2013 12:40 AM
mistahoo GE Window and door silicone
02-25-2013 11:55 PM
newms I get leaks sometimes out of the threading area of the bottle. I use aquarium silicone to seal it up, however the stuff isn't cheap. I like the idea of hot glue that was mentioned above.

I check for leaks by placing the whole setup under water in my water change bucket and blowing into the end where the gas would normally come out. If there is a leak, you will see the little bubbles streaming out of it. If the system isn't working, 99% of the time it is because of a leak.
02-25-2013 11:09 PM
m00se No glue. Just drill a hole under-sized for the tubing, cut the end of the tubing diagonally so you make a sharp angled end, and pull it through the cap with a pair of pliers. Air tight and fool proof.



02-25-2013 11:02 PM
Bandit1200 I used hot glue on mine.
02-25-2013 07:15 AM
sepulvd
What sealent is good for DIY yeast co2 system?

are you taliing about what to use to prevent co2 leaking from the cap where the tubing goes thru. if yes i usually use crazy glue around the tube snd cap. never had leaks
02-25-2013 02:30 AM
reconmarui
What sealent is good for DIY yeast co2 system?

What sealant works the best for this system? Also how can I tell if it is working?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 06:34 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012