|Topic Review (Newest First)|
|06-27-2013 05:31 AM|
|Ahlian||Its a good idea man and you have done a good work here after provide some beautiful colors to it. The thing i like is that we all should use coloring and designing in all the things either it is a reactor or car or anything else.|
|02-03-2013 05:51 PM|
I keep African Clawed Frogs, they were young at that point and just being funny.
As for the chamber, I payed way too much for mine, but it's whirlpool clear whole house filter chamber, you can get something similar cheaper. I was just inpatient.
|02-03-2013 05:11 PM|
|timdog||I think I found something that'll work, but what's up with those frogs in your avatar le0p?|
|02-03-2013 05:09 PM|
Seems like a good idea, I may try to do this but where'd you get the reactor chamber?
|02-02-2013 08:02 PM|
Originally Posted by cobra View Post
The way these things are built. I could just turn it around, with the exception of the t-piece that allows the air to enter the chamber. I'd have to re-plumb the other side to accomplish the same thing at this point.
|02-02-2013 07:46 PM|
Quick Cerges question:
I have a question with regards to flow direction (before I put finishing touches).
To be sure: The flow (from the pump/filter) enters the top of the housing. It then travels to the bottom. Water enters the riser (PVC pipe) from the bottom and flows upward and exits the top of the housing.
Reason I ask, it seems that I remember posts (can't remember if it was here or another website) where DIYers plumbed it the opposite way.
|01-31-2013 05:59 PM|
|le0p||Basically, it's what I had laying around. Seachem matrix, foam from a decommissioned sponge filter, and some scrubbies I tore apart (thinking they'd make a good media for water flowing through the air pocket). The scrubbies seem to work to an extent since I find waste built up when I clean them. I'm thinking of replacing them with the bio-balls you'd find in a wet/dry with the idea they'll provide more surface area for bacterial growth, since they'll be packed tighter.|
|01-31-2013 05:35 PM|
|discgo||Getting ready to build one myself. I plan on using filter floss in it hooked up to magdrive 2. I'm hoping it will diffuse the co2 and keep bacteria well in the same environment. What's the rhyme and reason to your media?|
|01-31-2013 03:19 PM|
Anyone have comments on this?
I'm thinking about gluing some screen or sponge over the water intake to disperse the incoming water more evenly over the scrubbies inside, giving a better wet/dry type of filtration. Also thinking of filling this with bio-balls instead of the scrubbies, since they would mostly be out of water.
|01-26-2013 03:54 PM|
DIY Bio reactor (Cerges design)
I built a Cerges reactor for Co2 but ended up not using it for that purpose (at least for now) so I decided about 6 months ago to try and use it for a bio reactor.
I connected the reactor to the return line of my Fluval 206. Since I had a T plumbed into the reactor I added an air pump figuring this would dissolve more oxygen into the tank allowing a better growth of bacteria. This also had an unexpected side effect, the pressure from the air pump created a large pocket of air where the the water trickles through the scrubs I pulled apart, not unlike a wet/dry filter. There is also a some sponge and bio-media on the bottom.
I wanted to get the forums opinion if my thinking is correct on this. I'm new to this kind of thing, so I figured I'd ask the experts. Also, I have a concern if this is taxing my canisters pump. The flow seems to be just as good as it ever has been and I can't hear any extra noise from the pump.
I added some pics of it up and running. Excuse the filthiness of the reactor and my cabinet, both need to be cleaned