|Topic Review (Newest First)|
|02-07-2013 03:45 AM|
|Jeffww||Will do. Although I wonder why it would work fine connected to the pc but not to the wall?|
|02-03-2013 11:23 PM|
|mistergreen||too much or not enough current maybe. Check on how much voltage & current for optimal function.|
|02-03-2013 11:13 PM|
|Jeffww||So I've got the pH displaying on the LCD at this point, working on button controls. However, I'm encountering some really weird problems. When I run the set up on its own directly from the outlet power it gets crazy pH fluctations. It's only stable when it's attached to my computer. I'm starting to think that my adapter is messed up.|
|01-29-2013 06:22 AM|
|Jeffww||That being said, it shouldn't really take that much current to run just a probe (a couple of ma at most) and an LCD though....So dividing the 5V pin seems pretty safe.|
|01-29-2013 03:54 AM|
It is definitely 500 mA maximum if drawn from USB. I am not sure what the maximum total current draw is when using an AC to DC adapter.
Each pin can supply a maximum of 40-50 mA, depending on which board revision you have.
To be honest, if you find yourself needing to draw more than 500 mA, you should be using a separate power supply anyway.
|01-29-2013 03:02 AM|
Really? I thought it was a 500ma max if it draws from a computer USB and 900ma if it took from a 9V adapter. Or rather, it would draw since there is no regulator as much as it could until something broke with 900ma being the general safety limit either in built to some arduino or just as a precaution.
edit: also why would I need resistors to bring down the current for the LCD? Why can't I directly wire them in parallel.
|01-28-2013 11:56 PM|
Originally Posted by Jeffww View Post
Alternatively, you could always just write one pin high so that it's at 5V (less efficient).
As a side note, the Arduino can only provide 500 mA maximum. There are other restrictions on certain pins (i.e. total of X to Y can only be 200 mA, etc). The Arduino website has the specifications for these current draw limitations.
|01-28-2013 10:59 PM|
you can use resistors to limit voltage and current. Ohm's law. Knock down to what you need for the lcd and leave it at 5V for the pH sensor.
Get yourself a breadboard and test things out first before you start soldering. There's a process that makes life easier.
|01-28-2013 09:47 PM|
Very interesting projects.
I have one question though. It seems that my probe won't work on 3.3V VCC. On 3.3V the readings constantly fluctuate +/- .2pH on continuous measurement. On 5V it's just fine. Is there a reason this could be happening? I think it's like 1 or two things.
1. I'm using a USB hub to connect to my laptop to power the arduino and probe so there might not be enough power to run everything at the stated voltage.
2. My probe which was shipped from china is just inefficient.
In the event that it's a probe problem is there a way to step up 3.3V to 5V in arduino? I'm worried I won't have enough space to run everything. I saw this thing called a logic level converter but I'm not sure that's applicable in this scenario... I don't have a multimeter with me but I guess I could try plugging it into my DC adapter to see if it works alright.
Or alternatively is there a way to split the 5V into multiple connection points so I can run my LCD and my probe.
I've read that I can split it through a parallel circuit with any number of devices whose total draw is less than 1A so that I don't fry my components. Does that sound right?
|01-28-2013 05:28 AM|
Originally Posted by Jeffww View Post
|01-28-2013 05:01 AM|
oh, gotcha. it costs the same to buy a CO2 sensor whose max is 36ppm
or a bit more ($250) for a sensor whose max is 300ppm.
|01-28-2013 04:44 AM|
|Jeffww||The idea is to use a gas permeable membrane to hold some 4dkh fluid and use the ph meter to measure fluctations in ph and translate to co2 concentration. Using the membrane increases response time for CO2 measurement.|
|01-28-2013 04:30 AM|
Arduino Diy pH probe
.010" or smaller of silicone sheet works great for separating gas from water. I don't see how this helps your ph sensor. Is it a gas sensor?
Sent from my iPad using Tapatalk HD
|01-28-2013 03:16 AM|
Just a quick question, has anyone gotten a membrane based CO2 meter to work yet? Like using a gas membrane like a kordon bag, vegetable bag or something like that to work with a pH probe?
I happen to have some parafilm I could get a hold of to try and make something workable with.
|01-28-2013 12:31 AM|
Yah the directions were all there. Atlas scientific does a really good job at explaining the set up.
All through ebay:
BNC break out and pH stamp were 28 + 8.00 + 6.50 shipping
Calibration fluid was $9 shipped (bought a few packets)
Probe was $17 shipped
I got it all via [Ebay Link Removed]
|This thread has more than 15 replies. Click here to review the whole thread.|