|07-31-2014 01:13 AM|
Definitely PM a mod like Somewhatshocked if you'd like to see it stickied.
I would say until such a time exists I'd email it to yourself or subscribe to it so you will always have it in your history somewhere.
|07-31-2014 12:02 AM|
|ErtyJr||Hey this is such an immensely useful post, is there any way we could get this stickied somewhere. There is a lot of info I would like to come back to later, as I'm sure others would.|
|07-27-2014 06:32 PM|
|07-27-2014 05:46 PM|
|07-27-2014 12:15 PM|
Hi I have a very simple mod that has worked wonderfully for my spec v. I replaced the lighting and now have very high lighting enough that my dwarf hairgrass is shooting off runners everywhere.
I went to home depot, bought a plain desk lamp, and then bought this 65 watt cree daylight floodlight bulb. Here is the link to it.
It is important to note that you Must use a bulb rated "daylight" it has the ideal spectrum.
I also bought some 1/2" pvc and fittings made by "sharkbite" from home depot and created a spray bar. The fitting was not a perfect fit I had to trim and sand down the elbow to get it to go into the piece the nozzel normal goes into. Then I had no surface tension so I drilled a 1/4" hole in the top to spray water at the surface. It is working well, but was still too powerful for my small apistogramma fry so I then used silicone on the inside of the elbow and blocked half the fitting. Since then it has been at a very good level. I then sprayed it black. Here is a picture...
And here is the whole tank. I adjusted the contrast a bit because the light is very very bright.
|07-27-2014 06:03 AM|
|07-27-2014 06:00 AM|
|07-26-2014 08:04 PM|
How did I miss this thread all this time?
Here are mine, all on a Spec V:
Lighting - force the stock light to have blue & white on together:
Wood base and 'hood' with glass lighting window
Don't have the tank anymore, one to many to take care of, RAOK'd it off to a fellow member here at TPT
|07-26-2014 05:01 PM|
I've had a couple Specs and love the look and form-factor but have always found myself wanting to tweak/mod the filtration. So, I finally decided to ditch the whole filter and go with a mattenfilter since I've been so happy with one (and Poret foam filters in general) in my main tank. The stock filter was very easy to remove - just silicone which cleaned up nicely with a razor blade. I used 1" 30ppi Poret and a small Jetlifter from swisstropicals.com, and I cut off the very bottom of the stock filter to use as a "gravel-guard" at the base of the foam.
I have the front edge of the foam lined up with the frosted glass edge, and a Hydor Theo fits nicely as does the stock top. The foam is cut just slightly wider than the tank and stays in place by itself. 1" Poret works ok in this tank as it's only 7" wide or so, but in a larger tank the 2" foam is much more stable.
Also, I really like these Jetlifters, but there's no reason you couldn't still use the stock Fluval pump and tubing - might need a little more room behind. Just make a small "x" in the foam with a knife and push the nozzle through for a tight fit, like I did with the Jetlifter.
Not sure what I'll use it for, yet!
|07-14-2014 05:45 PM|
|MABJ||I don't know much about the spec V lighting, but that seems like a simple wiring fix. Make the switch open the circuit for both, get both on.|
|07-14-2014 02:15 PM|
Just wanted to post how I plugged the hole at the bottom of the filter compartment. It was easy and can be done with water in the tank, which was the most important factor to me. I just cut a piece of electrical tape bigger than the hole itself and stuck it on the water colum side, yes it still sticks once it's wet. Barely visible, easy and cost effective.
Also I remember seeing a mod someone did with the stock light fixture. They made the day and night time blue leds come on at the same time, anyone have any info on that?
|07-04-2014 06:20 AM|
|MABJ||Has anybody here upgraded their lights? If so, PM me, I'd be interested in buying your stock light.|
|07-04-2014 04:49 AM|
|MABJ||Definitely post that pic. Welcome to TPT. Yeah I used plastic mesh|
|07-04-2014 04:34 AM|
|grammaknits02||Yes...Thank you for the replies and for the great idea of wedging something behind the basket to keep the babies in! I'm going to do that as well. The plastic mesh is pretty sturdy...it will work well for what I want it to do. In a while I will post a pic of my new little tank.|
|07-04-2014 02:38 AM|
|MABJ||Thanks for the replies guys|
|This thread has more than 15 replies. Click here to review the whole thread.|