|Yesterday 06:28 PM|
|Matt47890||Someone was saying you don't on the 20oz ones|
|Yesterday 06:19 PM|
Hydro tests are every 5 years as well and you'll need to do hydro tests on any pressurized Co2 canister that you use.
|Yesterday 05:10 PM|
|Matt47890||Actually I don't want this one lol I'd need to do hydrotests lol|
|Yesterday 03:48 PM|
|Yesterday 04:07 AM|
Can I use something like this
|11-05-2014 02:22 AM|
I made this with a ASA, FMF10BK Deltrol and the Watts needle valve ganged together.
I tried it with just the Deltrol valve and I wasn't able to adjust the bubble rate. With both of them together I can just barely do it.
I think folks are having troubles with the bubble rate slowing down for this reason: They crack the CO2 open which creates lots of back pressure, then they turn down the valve until they get the correct rate. Then as the back pressure is released the bubble rate slows down.
So what I do is get the bubble rate slower than I want... then adjust the rate up instead of adjusting it down.
I adjust the valve by tapping on it with something.... just light little taps and wait a bit to see if it changed...
|10-20-2014 07:33 PM|
One post that I saw in this thread (that also didn't receive any replies) suggested placing your thumb over the output of the tubing with the system up and running. This will force the Co2 out of any leaks that otherwise don't make themselves apparent.
I set my system up and didn't see any leaks but remembered that suggestion. Once I did that I found a good-sized leak from the compression nut.
|10-18-2014 01:25 AM|
Setup not working just right
i setup this and its great, but when i get the needle valve where i want it , it slows after a bit till nothing is really coming out. I submerged the threads all in water and found no leaks in anything.So im wondering if a bubble counter will fix this. I just want to set it at a constant rate so i dont have to fiddle with it all the time!!!!!
i just have the asa valve with a needle valve on a glass diffuser
|10-18-2014 01:12 AM|
|mkbojangles||I did this I tested for no leaks but when I let out the needle valve it does the rate I want but then falls off after a short time ... What do I need to make sure it stays constant|
|09-19-2014 05:18 PM|
This thread is fantastic! Been wanting a pressurized system for a while, but wasn't willing to spend the few hundred dollars that I thought they cost. It turns out I have almost all of the equipment needed (seeing that I used to play paintball a couple times a year).
I currently have an on/off that only has the one hole for the needle valve. If I were to go with this one, how would I know when my tank needs to be refilled? Would I just need to keep a close eye on my bubbles per minute to know when the tank is low?
EDIT: Nevermind. I found my answer on page 1219831928
|09-07-2014 05:18 PM|
|09-07-2014 04:30 AM|
Will this one
Fit this http://t.dickssportinggoods.com/prod...42723.4414642?
|09-06-2014 11:54 PM|
I can't believe this thread has over 300000 views. I guess it's just a testament to how cheap most of us are.
Has anyone hurt themselves yet?
|09-06-2014 08:45 PM|
Paintball Adapter Gauge leak
So my gauge is leaking from the tiny hole on the back. I heard that having the gauge is optional altogether, so what exactly do I fill the void up with? Is there some sort of nut I can and fill in the void, or what?
|08-25-2014 10:55 AM|
I would not recommend that you disconnect the setup on a daily basis; it would cause unnecessary wear and tear, and cause additional work.
The point of pressurized CO2 is to keep things as hands off as possible (in addition to having healthy plants).
If you do not intend to get a solenoid, I would just leave the CO2 running 24/7, albeit at slightly lower levels.
|This thread has more than 15 replies. Click here to review the whole thread.|