The Planted Tank Forum - Reply to Topic
Thread: Regulator - Cylinder seal Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
12-08-2012 08:00 AM
kevmo911 See if you can remove the nipple before you bother contacting anybody about a new nipple. Unless my 3M clone (currently in front of me) is dramatically different from the Milwaukee, there are no flat surfaces to use a wrench on, and it's not even clear that the nipple is attached via threads of any sort (size or standard), aside from a hairline crack between nipple and regulator body.

In short, I believe it's a one-piece unit, and there's no possibility of replacing the nipple. But I could be wrong.

In any case, even if it's possible to replace the nipple, getting Milwaukee to send you a couple of proprietary washers is still the cheapest option.
12-08-2012 07:34 AM
fishyjoe24 thanks I'll contact them.
12-08-2012 03:23 AM
danakin The other option is to go to a welding/gas supply shop like Airgas/Praxair and get a new CGA 320 nipple without the raised face. It should run about 10 bucks and some teflon tape. You simply* take off the old nipple and install the new one. Connect up to your cylinder with a regular 320 seal washer and leak check.

*I say "simply," however this may not be the case if the nipple was threadlocked really well in to the regulator body.
12-07-2012 12:44 PM
kevmo911 Don't try to use a permaseal. Contact Milwaukee for a some washers.

In a pinch, you can probably use a regular seal, but it's not something I'd recommend.

If the reg comes with a proprietary Milwaukee washer, you can re-use that for now. Just tighten it down hard.
12-07-2012 05:45 AM
fishyjoe24 so if I just bought a used 2.5 cylinder and used Milwaukee regulator. it's not a good ideal to use the perm-a-seals, or is it again Ideal. since it's used I want to put a new washer on it, and was going to put it on a 29g quick will be heavy planted, and wondering how long it will last.
12-06-2012 01:17 AM
kevmo911 Only because I've never seen it mentioned...

I accidentally cracked the flange of a Milwaukee nipple awhile back, while tightening it against a permaseal (I tried one this once, and will never do so again - standard nylon washers are dirt cheap and work flawlessly). I drank myself into a stupor out of frustration ...and several weeks later, had the presence of mind to wonder if the rest of the flange could simply be chipped off. 5 minutes of experimentation with a chisel and hammer left me with a (very) roughly flat surface, and I used that regulator for several months afterward with a couple (I refilled the cylinder) nylon washers.

I've since upgraded my regulator - a couple of times - and am happy I did. But that flange is just an annoyance, which can be dealt with via simple tools combined with brute force.
12-05-2012 07:51 PM
reel1090 Thanks exv152,
That is exactly what I am looking for.
12-05-2012 07:37 PM
exv152 Check this thread out
12-05-2012 07:08 PM
Regulator - Cylinder seal

I am using a Milwaukee co2 regulator and am trying to find a washer that will fit between the cylinder and the regulator. The ones I found on the internet said: "Not for use with the Milwaukee regulator".

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

For the best viewing experience please update your browser to Google Chrome