|11-27-2012 12:51 AM|
When people advise to squirt, they mean with a syringe. My BBA is on the retreat after direct application of Excel and continued trimming.
Sent from my iPad using Tapatalk HD
|11-26-2012 09:51 PM|
Sorry to be so dense, but I am beginning this battle too and need to know exactly how the squirting works. What kind of squirter do you use? Is this directly on a leaf that is temporarily out of the water (during a change)? Or in the vicinity of a leaf while still under water?
I can see using a squirt bottle filled with excel and holding each leaf above the water line during a change, but am not sure how underwater squirting would work if that is the answer. I do 25% water changes and some of my BBA is below that level. I'd do a bigger change if I had a bigger water aging tank, but I don't. This came on because of my more frequent water changes, which I need to do for the altums.
Damn you BBA!
|11-19-2012 11:47 PM|
|mistergreen||If you see a little BBA, squirt it with excel with the filter off for 15-30 minutes when you do a water change. The BBA will die off in a few days. It's my weekly routine now. It's no biggie.|
|11-19-2012 09:54 PM|
|11-19-2012 09:49 PM|
|TexasCichlid||Just came home, CO2 is on an hour before lights. Drop checker is yellow when lights come on.|
|11-19-2012 09:41 PM|
|11-19-2012 09:17 PM|
During my battle with BBA, I had the CO2 running 24/7 on a reactor and a bright yellow drop checker. The CO2 was so high that I lost every single invertebrate in the tank and unfortunately some fish, too.
The BBA was rocking at the end - seemingly unaffected by the high CO2.
|11-19-2012 08:50 PM|
|11-19-2012 08:42 PM|
Plantbrain has added wet/dry filters to all of his high light tanks, because they do a great job of dissolving O2 into the water. That could be a good next step for you. With increased dissolved O2, the fish can tolerate more CO2 in the water, so you can raise the bubble rate even more.
One problem with drop checkers is their very slow response to changes in CO2 in the water. When it takes hours to get to a yellow DC, that isn't because it takes that long to raise the concentration in the water, but because it takes that long for the DC to show it. If you have a good method of diffusing CO2 into the water it shouldn't take more than an hour, if that long, to reach the desired concentration of CO2 in the water. Perhaps a pH probe would react much faster?
|11-19-2012 08:37 PM|
take into account, if its still their, it can still reproduce. it can still grow on the slightest bit of unhealthy plant tissue...
water changes will help remove baby spores
organic objects that are inert are a great growing point for algae, these settle on elaves, hardwood, rocks,, etc.. even if u have a healthy leaf, if this stuff settles on a leaf for too long it can be the start of algae that eventually roots into plant tissues
|11-19-2012 07:24 PM|
Just an update. I have to trim about 10-15 leaves a day as it pops up. Also pops up on my glass. CO2 is waaaaay beyond the yellow point on my drop checker. Been dosing Excel at 5+mL per day every day before the lights come on. Been spot dosing the stuff on the glass, scraping off and siphoning when I can see it floating as a result. Getting a little frustrated.
Photoperiod is 6 hours now. Flow has slowed down so I am beginning to think that may be the culprit. CO2 is high enough now that it is overcoming my reactor and soda bubbles are showing up in the tank.
|10-26-2012 03:06 PM|
|TexasCichlid||I don't dose NO3 because my nitrates stay at 5-20ish ppm throughout the week between my aquasoil and feeding.|
|10-25-2012 11:57 PM|
|tetra73||Any reasons why you don't dose NO3??? For me, I tried to scrap them off if possible and then to siphon them out. I find that spot treating with Excel would tend to damage the leaves too. Same with H2O2. I simply just remove the affected leaves at the right time when there are a lot new ones growing. I also make sure CO2, ferts, and light are all balance. I mainly increase the CO2 by a bit, until the drop checker is yellow within 2 hours at the beginning of the light cycle. I have a 40g with a HOB filter and it takes a lot of CO2 to get to yellow by noon. I also do 3 40% WC per week. Using Purigen as well.|
|10-25-2012 10:47 PM|
if it helps syn.. i run a stream into my 29 gallon to keep the DC bright yellow, and i have a buttload of light.
algae is always ready to take hold, this is the dilema with high light, one slip and its there
keep trimming, adjust co2, keep it steady and eventuall plants will grow in and black algae will quit growing, anytime u get an unhealthy leaf though, guess what's gonna show up
|10-25-2012 12:05 AM|
Crazy...you and I have nearly the same set-up/issue.
I run the Finnex Ray2 on a 36G for 7 hours per day.
EI dosing, but my Nitrates run high so I add a little less KNO3.
50% weekly water change. I turn my CO2 on 2 hrs before light, but that is only because I either have a leak (that I can't find) or a very innefficient reactor. I'm running a freaking stream of CO2 to get my DC to a yellowish lime green. I turn the knob a bit more every couple days, but the BC is totally useless as a gauge in my case.
I check each evening and remove any leaves with even the slightest strings of BBA. I have only seen it on my Blyxa and my Acmela Repens stems. They are on opposite sides of the tank from each other. One is in a high flow area and the other not so much...this seems odd to me.
I had been running the light for 8 hrs and it was definitely worse then. I hate to cut to 6hrs as it feels like the kids and I hardly get to enjoy the tank as it is. I'm tempted to step down to the FugeRay. I could probably run the light for 10hrs a day, but some of my plants may not be happy with the lower output.
Anyway, hopefully one of us figures out a solution that the other can benefit from.
|This thread has more than 15 replies. Click here to review the whole thread.|