The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > General Planted Tank Forums > General Planted Tank Discussion > Co2 Regulator Deal?

Thread: Co2 Regulator Deal? Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-23-2012 05:29 PM
tylergvolk Yup, it's busted but I've gotten the unit to work regardless.

The solenoid turn off at night and comes back on with no problem.

The stability seems okay but it's only been a few days.
11-22-2012 04:56 AM
eisBear
Quote:
Originally Posted by tylergvolk View Post
Here is a better picture showing the gauge past 10 and it is not even hooked up to a cylinder



I will try your method and report.
Actually, that's a 10 kg/cm2 rather than psi, lbs/in2; sorry I missed that originally. No need to try my method if the regulator is not hooked up, just open the needle valve or the regulator valve while its not on the gas cylinder. If it doesn't go down, its more than likely just bad. YOu can replace it or not worry about it. The low, or 'working,' pressure gauge, IIRC, isn't even guaranteed to work on the new units.

Willing to bet, though, its busted. Milwaukee's method to adjust the bubbles/second doesn't rely on the low-side gauge anyway.
11-21-2012 09:14 PM
tylergvolk Here is a better picture showing the gauge past 10 and it is not even hooked up to a cylinder



I will try your method and report.
11-21-2012 05:42 PM
eisBear its hard to tell from the picture, it looks like the gauge on the right is at zero in that picture.

There are lots of ways to test the low pressure gauge. If you can dump the water from the bubble counter without tipping the tank (maybe use a baster or syringe and then unscrew it), you could close the regulator valve and then open the needle valve all the way with the solenoid on. If that doesn't peg it to zero, then it probably is foobed.

If you read the milwaukee instructions (google), it does say you don't need the right side gauge, just adjust bubble count with the regulator knob and then fine tune with the needle valve.

If you want to run a specific low pressure and the gauge is working, close the needle and open the reg until you get the low pressure desired. then open the needle until you get the bps you want. Milwaukee does not appear to endorse this method, internet rumors I've seen say that the bps is harder to keep adjusted using the Milwaukee recommended method. I don't think I've had mine long enough to tell you but I used a combination of methods and have about 20 operating psi and the bps stays stable for a few days at a time, pretty much.
11-21-2012 03:23 PM
tylergvolk Yesterday I went to AirGas and bought some Co2. Then, today I set this thing up today and I think the right gauge is broken.

If you look closer at the picture above you can see the right gauge is past 10psi. I think the gauge was blown but I am not sure.

When I set it up, I can see the gauge move when I release pressure slowly but it reads past 10psi however everything seems to work anyways.

What's the deal here?
11-12-2012 11:34 PM
tylergvolk
Quote:
Originally Posted by eisBear View Post
I found it was hard to get a good deal on a used regulator, seems like everybody knows their value. I wound up buying that model except new. Agreed, if it woks, its a good deal. That's a very popular model so you'll find others in the community with helpful tips.

Make sure to follow the very vague instructions for setting it up. I've seen some in the community say that the needle valve is easier to adjust and keep adjusted when the operating (low) pressure is at 20-30 psi, which contradicts slightly with Milwaukee's instructions.

I forget the setup instructions (which I'll have to look up again when I get the tank replaced/filled), but I remember one important step was to open the main valve of the tank very slowly so as not to blast the internal workings of the regulator. Make sure to look up instructions for it; as said, it is a popular model and the interwebs have lots of good info on setup and running it.
Cool, thank man. I need to purchase a 5lb. cylinder before I can even set it up. How much should I be paying for that?

Airgas will charge me $80 for a filled Co2 5lb cylinder. Seems a bit steep...
11-12-2012 06:49 PM
eisBear I found it was hard to get a good deal on a used regulator, seems like everybody knows their value. I wound up buying that model except new. Agreed, if it woks, its a good deal. That's a very popular model so you'll find others in the community with helpful tips.

Make sure to follow the very vague instructions for setting it up. I've seen some in the community say that the needle valve is easier to adjust and keep adjusted when the operating (low) pressure is at 20-30 psi, which contradicts slightly with Milwaukee's instructions.

I forget the setup instructions (which I'll have to look up again when I get the tank replaced/filled), but I remember one important step was to open the main valve of the tank very slowly so as not to blast the internal workings of the regulator. Make sure to look up instructions for it; as said, it is a popular model and the interwebs have lots of good info on setup and running it.
11-12-2012 04:12 PM
motorcycledaddy01 if it works, i would say its a good deal. regulator alone is around 100$ brand new.
11-12-2012 03:26 PM
tylergvolk
Co2 Regulator Deal?

Today, I purchased a Milwaukee C02 Regulator MA957 off craigslist slightly used for $50. I don't know much about co2, and I need to know if this was good deal?

Came with:
-Regulator
-Bubble Counter
-Silonoid
-Needle Valve


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 12:17 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012