|Topic Review (Newest First)|
|12-03-2012 10:09 PM|
Tested: Pump works beautifully, system works great. Takes up too much space inside the 20G tank though
Putting everything to the side, will try this system in a 55G when I eventually upgrade.
At that point I will have to choose between sump or no sump.....
|12-01-2012 08:04 AM|
|Sploosh||Found a pump, lightly used, very powerful. 350gph with high torque load capability. Now back to testing, hopefully this pump isn't too powerful for the 20G|
|11-29-2012 01:57 AM|
Only pumps I can find that are powerful enough to operate the system, are either too large/external pumps, or, are far too expensive ($150+) for me to justify using. (can only justify if I were using it for an external sump system, with the return under the gravel, blah blah blah.
Not sure of what to do next, maybe just move everything over and continue the 2-3 times weekly gravel vacuuming *sigh*
|11-18-2012 02:28 AM|
Originally Posted by In.a.Box View Post
Originally Posted by BenderBendingRodriguez View Post
Originally Posted by Hoppy View Post
|11-18-2012 01:31 AM|
|In.a.Box||what a UGJ? Heard of UGF but never UGJ.|
|11-18-2012 01:02 AM|
Originally Posted by Sploosh View Post
Yes, the pumps do chatter when the UG gets clogged but hovering the UG solves the problem. The UG takes about a 100 days to get clogged enough to make the pumps chatter.
|11-17-2012 03:23 PM|
Thank you very much for the link, Great idea/setup. Would work for me if I had a larger tank, and if I wanted to go the ugf route.
Based on the calculation you provided, I will need 200 square inches for the ugf, (based on the pump sitting here) my tank bottom is 288 square inches (12"x24").
Seeing as the gravel is 80% covered in plants/rocks/wood, I don't think this will work for my application.
Also I don't like pulling water through the gravel, due to my tank being overstocked, my biggest problem right now is constant gravel vacuuming. (as in every 3-5 days) I can see my intake pipes getting plugged quite often.
I am attempting to create an upwards current under the gravel on as close to 100% of the tank bottom as I can.
It is a great idea/setup, it's just not what I am attempting to do.
I'm trying to do more of a reverse ugf setup with a higher flow than just ugf plates with a reversed powerhead. (have to push through 4" of gravel on one end)
What kind of pumps did you use in your system? Do they "chatter" when backloaded?
|11-17-2012 10:23 AM|
|essabee||If go through this http://www.plantedtank.net/forums/sh...ad.php?t=99605 it might help you.|
|11-17-2012 02:45 AM|
Just tested the pump, it won't handle the back-pressure of only 3ft of 1/2" tubing, nevermind restricting the flow, just chatters like crazy.
Now searching for a pump that can handle the back-pressure of the system.
|11-17-2012 12:07 AM|
Thank you for the replies,
I have gone over materials again, and am going to use 1/2" reduced to 3/8" tubing.
I will be using a spiral to avoid 90 degree bends (to prevent turbulent backpressure on the pump). Also two spirals will cover 90% of the bottom glass, and, with available materials, a grid pattern would only cover 72% of the bottom glass.
I am still struggling with size of holes, and how many. For testing I was going to use 12 1/16" holes on one closed loop spiral and see what happens. Depending on how the test goes, I may use the two opposing pumps idea.
|11-16-2012 05:29 PM|
|rrastro||You're more likely to have pressure differences from the front to the back of the line if you set the tubing in a spiral. A grid or manifold provides the same filtration effect using less tubing with even pressure across the system. 1/2" will work fine in this type of setup, with only one pump needed. I had a smaller pump running a similar system in a 20L. Wash the heck out of whatever substrate you use. I used turface and even with thorough washing the system blew out fine dust into the water as the substrate degraded from the constant flow of water.|
|11-16-2012 04:53 PM|
Any system that pumps tank water under the substrate, so it passes through the substrate back to the tank, is a under gravel filter. Your reasons for using it don't change what it does. The goal should be to get roughly equal flow from every hole in the tubing. That requires that the total area of the holes not be much greater than the cross section area of the inside of the tubing. If the total area of the holes is much less than the area of the tube ID, you get strong jets of water from each hole. If the total area is much more than that of the tube ID, you get slower jets, and the holes farthest from the inlet to the tube may have very little flow out. When I was using this type of filter I didn't notice any stirring up of the mulm on the substrate. The flow from the jets gets diffused so much by the gravel that you can't see anything happening.
If there isn't much gravel over an area of the jets, you get a miniature gravel volcano, which doesn't look good. So, it seems that you have a choice of no visible effect or a bunch of miniature volcanoes.
|11-16-2012 04:44 PM|
After some "deep" thought, I may just use 1/2" tubing in the whole system. Thoughts?
It'll probably be 16ft total tubing.
|11-16-2012 04:55 AM|
Originally Posted by Sploosh View Post
|11-16-2012 04:10 AM|
|Sploosh||(1-4" deep) --- of Gravel, not waste|
|This thread has more than 15 replies. Click here to review the whole thread.|