|Topic Review (Newest First)|
|11-13-2012 02:05 PM|
Originally Posted by TexasCichlid View Post
It's a pretty simple physics principle that can be applied to any vessel that would be suitable to use in our hobby.
If one wanted to do this in 5gl tank they could silicone in a false bottom piece of glass that has 1/2" pitch from one end toward the syphon inlet. Then cover with a single later round river stone/pebbles.
I see the design merit in a fish room for use in holding tanks/ Q-tanks for adult fish.
|11-13-2012 01:33 PM|
Originally Posted by jimmytruong87 View Post
|11-13-2012 11:10 AM|
|jimmytruong87||It only works for 3 -5 gallons ( small tank)|
|11-13-2012 09:19 AM|
|Sethjohnson30||I want to make one of these out of a plastic 5g water cooler jug|
|11-13-2012 09:07 AM|
Originally Posted by DogFish View Post
|11-12-2012 10:11 PM|
Every drilled tank is already something like that. With the proper plumbing any tank can be 'self cleaning' in the same way that one is. I do not see it working for a planted tank, though. The idea that waste falls through the substrate may be OK for a non-planted tank. Coarse gravel would do what the marbles are doing in that set up.
The larger floor of a real tank would need more of a 'system' for cleaning, though. Under gravel plates, for example. Stick the siphon down the up tubes, and clean under the plates. I did it that way when I was trying the reverse UGF concept.
Sure looks like copper outlet. I am not sure that it is in contact with the water all the time, though. Only the out flowing water during a water change.
|11-12-2012 08:19 PM|
Not paying $70 for a vase with a tap .
Rather get an Ebi or Flora for that price. 16x bigger, filter, lights, substrate and bonus supplies.
|11-12-2012 08:09 PM|
|TexasCichlid||The fact that they have raised 53k+ dollars for a glass vase with an overflow spigot on the side baffles me.|
|11-12-2012 05:29 PM|
im considering the DIY option at this point!!!
i saw a 5 gallon a petsmart the other day when i was getting emergency crickets, that tank has "drill hole in the side" written all over the side of it in my head
|11-12-2012 04:42 PM|
Originally Posted by SpecGrrl View Post
I also noticed the water level would stay below the overflow so there would be little if any backwash effect even if there was copper contact at any point.
Personally, If clean a 1 qt, jar is that "icky" or so much trouble one shouldn't be in this hobby.
|11-12-2012 04:42 PM|
No Clean Aquarium
Originally Posted by wkndracer View Post
No such system in my tanks. The idea of a maintenance free tank is essentially the same, no water changes, but I emerse the roots of land plants in the tank water. The roots take in the nitrogens the fish produce and the water stays pure.
|11-12-2012 04:24 PM|
If it is copper, dead shrimpies.
Otherwise, I agree, good for shrimp, not bettas.
Also, a Pre-filter would be oh so necessary.
Their demo video is kind of horrifying bc the poor betta gets smashed by the water being poured in.
|11-12-2012 04:11 PM|
|ony||+1 way too small for fish. Love it as a desk ornament though, would look great with a couple of my favourite plants. Also is that copper I see on the spout?|
|11-12-2012 02:44 PM|
O.K. so who's going to be the 1st forum member to do a DIY Knock Off?
This might be worth buying a glass cutting bit for.
|11-12-2012 02:41 PM|
Agreed on the comments about using as a fish tank.
There's also not enough surface area for gas exchange even if the heat issue was resolved.
I do see merit as a shrimp bowl for a office desk top.
|This thread has more than 15 replies. Click here to review the whole thread.|