The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment > Atomic CO2 Regulator V3

Thread: Atomic CO2 Regulator V3 Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-10-2012 10:12 PM
AUvet14 No need to fully submerge the diffuser in it. Just put enough of the detergent on to make a liquid coat around the diffuser. Just a thin layer should be all you need.

Sent from my HTC One S
10-10-2012 09:56 PM
mcaquatic
Quote:
Originally Posted by AUvet14 View Post
It is probably the diffuser needing to be cleaned. I have this regulator as well and I'm using a GLA atomic diffuser. My bubble rate slowed down as well but after I cleaned the diffuser the mist was finer and the bubble rate returned to normal. You might have to clean it really well using the acidity detergent if you have it. Use just enough to coat the outer surface and let it sit for 30 min, then do 50/50 bleach and water bath for a little bit and rinse in fresh water using a dechlorinator like Prime or whatever you typically use. Let it dry completely, which might take a while, and it should be good as new. I cleaned mine a couple times because it was really clogged but I was only using the acidity detergent and I didn't give it time to sit for 30 minutes. I contacted GLA about it and they gave me the more detailed cleaning instructions. Hope this helps.
What do you mean by just coat the surface? I have the detergent. Do you just fully emerse the diffusor in a cup? Thanks
10-10-2012 02:24 PM
AUvet14 It is probably the diffuser needing to be cleaned. I have this regulator as well and I'm using a GLA atomic diffuser. My bubble rate slowed down as well but after I cleaned the diffuser the mist was finer and the bubble rate returned to normal. You might have to clean it really well using the acidity detergent if you have it. Use just enough to coat the outer surface and let it sit for 30 min, then do 50/50 bleach and water bath for a little bit and rinse in fresh water using a dechlorinator like Prime or whatever you typically use. Let it dry completely, which might take a while, and it should be good as new. I cleaned mine a couple times because it was really clogged but I was only using the acidity detergent and I didn't give it time to sit for 30 minutes. I contacted GLA about it and they gave me the more detailed cleaning instructions. Hope this helps.
10-10-2012 01:42 AM
crice8 No you do not have to worry about an EOTD at all with the GLA atomic diffusers.
10-10-2012 01:00 AM
mcaquatic
Quote:
Originally Posted by PlantedRich View Post
Not to panic but when you say your tank is low, it makes me nervous! Are you up on End of Tank Dump? EOTD can come around when the liquid is gone from the bottle and the pressure begins to drop. a weird thing with regs is that can cause the remaining gas in the bottle to go into the tank in a "dump" which can be very bad for any fish.

The bubble rate changing may be because the needle valve is not quite as good as some. Not up on the diffuser end though so I'll let others have a go at that.

With this reg end of tank dump should not be an issue. It is supposed to be able to run until the tank is completely empty. It is supposed to have a pretty good quality needle valve and others using it don't seem to have an issue so I hope that is not the case.
10-09-2012 11:32 PM
PlantedRich Not to panic but when you say your tank is low, it makes me nervous! Are you up on End of Tank Dump? EOTD can come around when the liquid is gone from the bottle and the pressure begins to drop. a weird thing with regs is that can cause the remaining gas in the bottle to go into the tank in a "dump" which can be very bad for any fish.

The bubble rate changing may be because the needle valve is not quite as good as some. Not up on the diffuser end though so I'll let others have a go at that.
10-09-2012 04:28 PM
mcaquatic
Atomic CO2 Regulator V3

so i got an atomic CO2 regulator V3 last week to replace my old regulator to hopefully make life easier. It is running on my 90g which has an inline atomic diffuser. I set the bubble rate to 5/s which is maintains all day, but then the next day the bubble rate is at a bout 2.5 bubbles per second. I can't find any leaks. My diffuser hasn't been cleaned yet and it has been almost three months. Could this be my problem? My tank is low, but that is not supposed to be an issue with this diffuser. Any thoughts?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 08:58 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012