|08-18-2012 07:56 PM|
Here is a similar thread that Im talking about. They use egg crate.
See Post #7.
|08-18-2012 06:40 PM|
Good call herns, I will go out and get one of these from Home Depot and cut it to size ...
Lifting the light is really not an option since I have a DIY wood canopy over the tank.
|08-18-2012 06:33 PM|
|08-18-2012 03:04 PM|
You can lift your bulbs up.
Some dark areas shouldn't be a big problem though. You can turn lights on after the situation will be under control.
|08-18-2012 02:33 PM|
Thanks reiben. I will cut back on my lighting. The problem with shutting off the 2x39W is that it creates some dark areas in the back of the tank and all the plants start bending forward towards the other fixture.
Is there a way to diffuse light so that it is more even?
|08-18-2012 11:54 AM|
There is still too much light. My sugestions:
1) Scrub as much algae as you can.
2) Lower the light - 2x54W will be enough. No need to use extra 2x39W.
3) Improve water circulation and increase CO2 levels. Excel will help too.
|08-17-2012 06:40 PM|
Come back on this thread when you have successfully got rid of BBA. We'd like to know result.
|08-17-2012 06:38 PM|
|08-17-2012 06:35 PM|
|herns||You can spot treat the remaining BBA with Excel, Hyrogen Peroxide or Metricide 14. The best time to do this is when you do water change where BBA is exposed out of water. Squirt excel directly to BBA and leave for few minutes. Add water back to your tank. In few days you will see BBA will start turn to purple/ red, dying.|
|08-17-2012 05:47 PM|
If BBA stops growing, do I still need to remove what is currently in the tank? Since it is so widespread, what is the best approach to this?
|08-17-2012 05:43 PM|
BBA like to grow when CO2 is low. Ive been experiencing this many times.
Get a CO2 indicator, crank up CO2 and watch your dosing.
|08-17-2012 04:16 PM|
Need help with BBA
Sorry about this longish post ...
I need help with my tank overrun with BBA.
90 gallon heavily planted tank that has been running for 1 year now. It is quite heavily stocked. I run pressurized CO2 and the drop checker is green-yellow. EI dosing with 50% weekly wc. Two Eheim cannister filters 2215/2217. 78F. This is a 24" tall tank and I have an Odyssea 4x54W fixture and a 2x39W fixture that sit on top of the tank. Light runs 1.5 hours in the morning and 7 hours in the evening.
I have been plagued with BBA (only recently identified as BBA) for a while now. Here is my current course of action:
- Cut lighting. I have shut off 2 of the 4x54W bulbs.
- Started using Flourish Excel per Seachem recommended dosage. However, this is quite expensive for a 90 gallon and I would like this to not be a permanent thing.
- I have two Hydor Koralia powerheads that normally provide plenty of circulation (I cannot keep any floating plants!) and surface ripple. However, one of them is out of commission temporarily. I lost a spacer down the sink when cleaning it and Hydor is sending me a replacement.
The bba started when I was using all my lights and was too scared to bump up the CO2. I feel that the cause may have been addressed. I am wondering how to get my tank to a good starting point.
I have read the recommendations about spot treatments and trimming. However, the bba is very widespread and spot treatment is daunting ... where do I start? Also, trimming may not work since most of the bba is in the mid to lower levels. I would end up taking out whole plants.
My plants ... Ludwigia, Rotalla, Anubias, Java Fern, Amazon sword, Crypt Wendti, Cabomba, Elodea, stargrass
Fish ... rainbowfish, harlequin rasbora, rummynose tetra, gold barbs, julii cory, roseline sharks, bnp.