|02-25-2014 02:54 AM|
Sorry im a terrible cameraman. If the images r not upright, idk what that about tapatalk is making them all rotated funny.
This is on my 25 gal. Its powered by a rena xp2 and has an inline diffusser also so....not the 300gph rated but its pretty close i'd say. Has a diy spraybar too. Pvc is awesome!
Hard to get a good pic but If I remember correctly its 2" pvc with a weird union. I just took the heater in lowes and pieced it together. Lol why not. Used some silicone to seal the heater in. And and little reducer ro add the water dump valve. Usually I just run that house out the window. Unless im out of house plant water. Those buckets r only for filling and acclimating.
Its a 100w aqueon. I only keep it at 75f but it has no trouble with that. Sometimes my water change water is a little cold and it goes from 70-75 in less than an hour. I use two digi thermos on opposite sides and they are within a degree so its pretty even temps.
Pretty easy could be built for any size I guess. I dont unplug it or anything when I stop flow or whatever. Been working over a year now.
If u got any questions let me know. Sorry for the bad pics.
|02-25-2014 02:29 AM|
|02-24-2014 07:50 PM|
|jeffdenney||I can upload some pics later tonight when I get home. I built a super simple pvc one. Took 5 min.|
|02-24-2014 07:41 PM|
|kman||Old thread, I know, but I'm researching the photo links are broken. Are they still available?|
|06-23-2013 07:07 AM|
|pandamonium||That was pretty much it It's not hard to build and it definitely saves money. I took my heater off though because I am no longer using a canister on that tank. PM me if you have specific questions aquah20!|
|06-23-2013 02:09 AM|
|07-24-2012 12:51 AM|
|pandamonium||Yeah I was in your shoes before. I was going to get the Hydor but they are huge and the knob turns a bit too easily from what I am told. Both problems easily fixed but I figured that this casing cost me about 12 dollars to make and the heater was 32 through Dr. Foster and Smith. Still cheaper than the Hydor and I must say, about 5 weeks later, my temperature remains at 81 with almost no deviation. So I am happy|
|07-23-2012 10:45 PM|
|ayobreezie||Thanks, man.. I was gonna order a hydor, but I got one of these laying around I might try this first.|
|07-06-2012 02:41 AM|
|07-06-2012 01:31 AM|
|MichaelMcG||did you hook it up to your inflow or outflow?|
|07-05-2012 02:44 AM|
|pandamonium||yeah i read many reviews on the eheim series. i believe this one i bought after eheim was bought out or something so it isnt the old school nuke-proof heater but it still got good reviews on this forum and others too. the way i assembled the top was to silicone it up to the edge. any water that lands on top would fall off yes. i had an incident with my heater and turkey baster full of bloodworms and fall off the bloodworms did...onto my floor but at least no water got through that i knew of.|
|07-05-2012 02:41 AM|
|PlantedRich||Heaters are improving and the Penn-Plax is among the worst design-wise. Just knowing Ebo-Jager, I would expect better and I can see from the outside some good points. The design of the top of your heater looks good. If you spill water on your heater it is likely to run off the edges. The brown cover on the Pen-Plax is a cup where the adjustment sets. Any water spilled on it will set in the cup and eventually find it's way along the screw and inside. I know we are not supposed to get water on them but that is like telling a five year old not to get wet when it rains. Just happens!|
|07-05-2012 02:09 AM|
|07-04-2012 10:42 PM|
|MichaelMcG||nice job! thanks for the pics. im going to be doing something like this in the near future. i like how you used a reducer instead of just drilling a hole in something lol. ill have to see what i can do with mine because my submersible heater looks a little thicker than yours.|
|07-04-2012 09:30 PM|
I was just in line to post a blurb about why heaters may fail so some of the info is relevant to your question about the "bimetal".
While there are various ways to control heaters, this is kind of prepresentive of many brands. This is a really cheap Penn-Plax while others use somewhat better parts but still many use the design and they have the same problems.
This is the layout of the main parts.
Rather than step all over your build I will post the details of heaters in a seperate item.
Your build looks like a nice job that should avoid many of the problems with heater failures.
|This thread has more than 15 replies. Click here to review the whole thread.|