The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Fertilizers and Water Parameters > adjusting ph by mixing well water and RO

Thread: adjusting ph by mixing well water and RO Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-02-2003 11:20 AM
m.lemay Keep your kh around 4-5 degrees. That'll give you sufficient buffering for co2 injection. Ph readings can be very deceptive with water that has a low buffering capacity. Use kh values instead of ph to set buffering.

Marcel
08-02-2003 04:29 AM
mr hyde Mike,
I'm planning on getting a controller soon with pressurized system. I was curious as to what PH to start out at before injecting CO2. I'll probably be adding more tap water to the tap/RO mix to bring the PH up to around where your's is instead of 6.8 where I am now. Then bringing it back down with CO2. Thanks , much appreciated!
08-01-2003 10:20 PM
Momotaro I do just about the same thing, mixing RO and tap water. Out of the tap my pH is about 8.2, a wee bit high for my taste. My tap / RO mix brings my pH to 7.2 and my KH to 4. I then inject CO2 and bring the pH down to 6.8.
Since you are using DIY CO2 injection, not pressurized, how do you plan on using a pH controller? You need a regulator and solenoid to run a controller.

Mike

Bumping your KH up a wee bit might not be a bad idea.
08-01-2003 06:34 PM
Guttboy My tapwater is 7.8 pH, KH 125, GH 143

Will drop pH here when I get the CO2 system on monday. Will let you know how things work out!

Mike
08-01-2003 05:53 PM
Angel12 If I have converted right then Your KH is 3 and GH is 1 ..
Take a look at this table it is very informative and will enable you to work out the correct PH you need to hit for maximum benefit

http://www.csd.net/~cgadd/aqua/art_plant_co2chart.htm

from your current readings 6.8 is right for the amount of Kh you have ..you could take it down to 6.6 ...

08-01-2003 05:18 PM
mr hyde Rex
This is a 46 gal tank w/DIY CO2, 2 bottle set up, going into the filter intake of Eheim. The KH is 70mg/L and the GH is below 20mg/L. This is using a Hagen test kit, hopefully it's accurate. I haven't tested the CO2 in the water yet.
08-01-2003 12:42 PM
Rex Grigg What is the size of your tank and are you using DIY CO2 or pressurized? Also what are the kH and gH readings in your tank?
08-01-2003 05:16 AM
mr hyde I've been mixing 1 part tap water to 5 parts RO water to get a PH of 6.8 before adding it to the aquarium. Once it's in the tank it never seems to go up or down much at all which is good. What I'm wondering is what PH do most of you have to start out with before injecting CO2 and bringing it down. I've heard of a lot of people having a PH of around 7.2-7.4 and then adding CO2 to bring it down to 6.8 and using a contoller to keep it around there. Mine is always at 6.8. If my CO2 stops it still stays at 6.8 and after a day of plants using it up it still seems to stay the same. I'd like to add more tap water because my GH and KH is really low but am wondering if I'll still be able to get my Ph down to a decent level if I start out at a PH of 7.2. Adding the extra tap water will raise the PH. It seems like from what I've heard others say that if I'm starting with a PH of 6.8 from the start then once it's in the tank with CO2 being added it would be going down lower like to 6.0 which wouldn't be good of course. Maybe I should just leave it alone. The reason I ask is I'm thinking of adding a PH controller and if my PH is always at 6.8 then the monitor would be reading everything as ok and not ever adding CO2 even though there would be a need for it. I hope I explained this right. Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 07:22 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012