The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY > Paintball Co2 Injection DIY Setup with Tons of Photos

Thread: Paintball Co2 Injection DIY Setup with Tons of Photos Reply to Thread
Post Icons
You may choose an icon for your message from the following list:

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
Yesterday 06:28 PM
Matt47890 Someone was saying you don't on the 20oz ones
Yesterday 06:19 PM
Originally Posted by Matt47890 View Post
Actually I don't want this one lol I'd need to do hydrotests lol
It says fresh hydro test.

Hydro tests are every 5 years as well and you'll need to do hydro tests on any pressurized Co2 canister that you use.
Yesterday 05:10 PM
Matt47890 Actually I don't want this one lol I'd need to do hydrotests lol
Yesterday 03:48 PM
Originally Posted by Matt47890 View Post
Can I use something like this
Yes but you'll need other parts/equipment besides just that.
Yesterday 04:07 AM
Matt47890 Can I use something like this
11-05-2014 02:22 AM
suds1421 Everyone,

I made this with a ASA, FMF10BK Deltrol and the Watts needle valve ganged together.

I tried it with just the Deltrol valve and I wasn't able to adjust the bubble rate. With both of them together I can just barely do it.

I think folks are having troubles with the bubble rate slowing down for this reason: They crack the CO2 open which creates lots of back pressure, then they turn down the valve until they get the correct rate. Then as the back pressure is released the bubble rate slows down.

So what I do is get the bubble rate slower than I want... then adjust the rate up instead of adjusting it down.

I adjust the valve by tapping on it with something.... just light little taps and wait a bit to see if it changed...
10-20-2014 07:33 PM
Viper One post that I saw in this thread (that also didn't receive any replies) suggested placing your thumb over the output of the tubing with the system up and running. This will force the Co2 out of any leaks that otherwise don't make themselves apparent.

I set my system up and didn't see any leaks but remembered that suggestion. Once I did that I found a good-sized leak from the compression nut.
10-18-2014 01:25 AM
Setup not working just right

i setup this and its great, but when i get the needle valve where i want it , it slows after a bit till nothing is really coming out. I submerged the threads all in water and found no leaks in anything.So im wondering if a bubble counter will fix this. I just want to set it at a constant rate so i dont have to fiddle with it all the time!!!!!
i just have the asa valve with a needle valve on a glass diffuser

thanks !
10-18-2014 01:12 AM
mkbojangles I did this I tested for no leaks but when I let out the needle valve it does the rate I want but then falls off after a short time ... What do I need to make sure it stays constant
09-19-2014 05:18 PM
Viper This thread is fantastic! Been wanting a pressurized system for a while, but wasn't willing to spend the few hundred dollars that I thought they cost. It turns out I have almost all of the equipment needed (seeing that I used to play paintball a couple times a year).

I currently have an on/off that only has the one hole for the needle valve. If I were to go with this one, how would I know when my tank needs to be refilled? Would I just need to keep a close eye on my bubbles per minute to know when the tank is low?

EDIT: Nevermind. I found my answer on page 1219831928
09-07-2014 05:18 PM
Originally Posted by Silvernb03 View Post
Was it your intention to post a link to pros wear?
09-07-2014 04:30 AM
Silvernb03 Will this one
Fit this
09-06-2014 11:54 PM
oldpunk78 I can't believe this thread has over 300000 views. I guess it's just a testament to how cheap most of us are.

Has anyone hurt themselves yet?
09-06-2014 08:45 PM
Paintball Adapter Gauge leak

So my gauge is leaking from the tiny hole on the back. I heard that having the gauge is optional altogether, so what exactly do I fill the void up with? Is there some sort of nut I can and fill in the void, or what?
08-25-2014 10:55 AM
Darkblade48 I would not recommend that you disconnect the setup on a daily basis; it would cause unnecessary wear and tear, and cause additional work.

The point of pressurized CO2 is to keep things as hands off as possible (in addition to having healthy plants).

If you do not intend to get a solenoid, I would just leave the CO2 running 24/7, albeit at slightly lower levels.
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT. The time now is 11:12 AM.

Powered by vBulletin®
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012