The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > DIY > Attaching airline tubing.....

Thread: Attaching airline tubing..... Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-29-2003 01:24 PM
JamesHoftiezer I know some one on aquabid sells adpters just for this, but Rex's method will work just fine as long as its a tight fit.

If the seal isn't tight or you have a habit of pulling the hose out ( ) then the silicone or epoxy will work great. If you do use the silicone or epoxy just turn the hose/cap assembly upside down and apply a generous amount. In this case generaous would mean less than 1/2 TSP.
06-22-2003 07:39 PM
aquaverde Epoxy would probably be a little more bulletproof than silicone, too.

You know, if it weren't for duct tape and sealant, I would be totally inept.

James
06-22-2003 05:06 PM
digger Some 90 second epoxy will work well if you need to plug any holes or fill any small gaps. Just follow the directions on the bottle.
06-22-2003 02:48 AM
aquaverde I was going to follow Rex's method until I found I didn't have an 11/64ths bit around. I went a little larger, and the hole was a little boogered up (juice bottle top) after I got through. I started the yeast into a Duetto filter, and the output was too much air considering how much the yeast was working. I just put a little aquarium silicone around the tube on the cap and it sealed right away.

James
06-22-2003 02:37 AM
corey Before I had my pressurize system I did the same thing Rex did. Its simple no mess and worked fine for me for years.
06-21-2003 07:24 PM
anonapersona I used "Liquid Nails" clear caulk or adhesive or something that was here in the garage, from Home Depot or someplace like that. The aquarium silicone had failed and I was kind of frantic, and I used it while the unit was still going. It worked great, sealed even though the top was under slight pressure.
06-21-2003 01:40 PM
Rex Grigg Drill a hole smaller than the tubing in the cap. I have found that a 11/64th hole works great with the normal green silicone tubing. Then cut the tubing at an angle. Thread the end of the tubing into the hole and pull it the rest of the way through with pliers. It should be VERY HARD to pull though. If you have drilled the hole the right size you will have a gas tight fit.
06-21-2003 08:05 AM
Wasserpest There are many ways... I found mine:

I use one of the black dripline connectors that have barbs on both ends.
I cut it in half (carefully, with a sharp knife), so one is actually good for two bottles!!!
I drill a hole into the bottle cap that is just a little bit smaller than the black thingy (so I can push it in with a little effort)
I add a little adhesive glue to the black thingy, and push it into the hole (with some pliers, or pushing the cap against something sturdy). The glue is pushed out on the sides and provides a tight seal.
Then I let it dry for 12 hours. Okay no I don't, but maybe it would be a good idea.
So now you have the bottle cap with the barbed thingy... time to push the airline over it and screw it onto the bottle.

Works every time. I tried Rex' method using only the airline, but wasn't that successful.

Wasserpest :mrgreen:
06-21-2003 06:52 AM
Work In Progress For a DIY yeast bottle thingy.......
A friend and I were discussing this and it would appear there are several ways to do it.
I have seen barbs and some plumbing fixtures listed in other posts.........and was wondering about the easiest way of attaching the cap and tube mostly.

I am sure you experts can help me out........

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 03:10 PM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012