|11-12-2013 03:04 PM|
I am going to use my old sea clear sump that I had for my reef tank, and fill with water to submerge the bioballs, and run air stones from an air pump under the bioballs making it a moving bed.
And with filter pads above it where the drip tray way.
Love the idea of keeping the sump for my 75 gallon planted tank, constant water level in the display tanks, no surface scum, and hide all of the equipment, Probably make use of a phosban 150 reactor as a CO2 reactor down in the sump as well if deemed necessary.
Have a nice CPR 100 overflow, with a aqua lift to keep the syphon auto start.
|11-08-2013 01:59 AM|
|anastasisariel||75 gallon tank with 29 gallon tank converted to sump.|
|11-08-2013 12:53 AM|
|crazymittens||Oh...I'm confused. Drip tray area is the wet/dry...stuff above water = dry, stuff below water = wet. Wet/dry. No? :S|
|11-07-2013 07:10 PM|
For us would it not be considered a wet dry filter
Sent from my iPad 3 using Tapatalk HD
|11-07-2013 11:34 AM|
The downside to a shorter (height) sump is you then can't do quite so much wet/dry functionality - it requires a certain amount of height above the water level for the dry portion. I agree it makes maintenance trickier in a smaller cabinet, though.
The water pressure you're dealing with really isn't much...I'd just DIY the silicone. If you had a 100 gallon sump...then maybe more attention to detail would be required...
|11-07-2013 06:01 AM|
I think I am going to use a 30L instead of the 29 that is currently in use. The 29 works but is so tall that it makes maintenance a little difficult. I think something shorter and longer is better. The other nice thing is I can take my time building the 30L so when I take everything down it will already be done and the reassembly will be faster. The downside is I was going to use that 30L to house my fish while it was down. Maybe I need to get on craigslist and look for a temporary home.
All things to think about and figure out how I am going to do this.
|11-06-2013 11:33 PM|
|Legot||Can I join the club?!?! I've got a 10g reverse night cycle planted sump on my 20long running a 6" DSB.|
|11-06-2013 11:27 PM|
|crazymittens||It'll eventually cure (as long as we're not talking 1" deep), but the absolute minimum is 48 hours, recommended a week. Don't forget...it off-gasses ammonia!|
|11-06-2013 05:03 PM|
|11-06-2013 03:23 PM|
IIRC you can get the foam at places like Big Al's (LFS), or off amazon in big sheets/rolls.
I had no issues with silicone/acrylic - just used a lot. Be sure to let it cure for 48-72 hours minimum, most especially if you are really gooping it on. After 24 hours anything thicker than 1/4" will still be liquid on the bottom.
Note that the design you're showing - the first baffle is too high (well, no point in being that high). The water level in that first section will only get as high as the next baffle over.
Also, there's no 'dry' section to this, i.e. for a drip tray. Everything I've read (barrreport, here) indicates that freshwater sumps really benefit from a drip tray so you get more types of bacteria.
For mine, I have a higher first baffle (raised 2" off the bottom) than necessary - aesthetics, but a functional mistake. Note the second baffle (which touches the bottom of the sump) has the drip tray immediately flowing off the same height.
This design allows me to have a wet/dry sump with only two baffles. The drawback is that the entire unit must be sealed to reduce CO2 off-gassing.
|11-06-2013 04:32 AM|
Hey guys, I'm going to redo my big tank and I figure while I've got it down I might as well go ahead and do the sump as well.
I originally used plexiglas as dividers but those started washing out after a year or so. I'm thinking this time I will use glass dividers but I want to know of any tricks y'all used to make sure the silicone didn't wear out and give way over time.
I plan to redo my sump with a design similar to this:
Now this one has very little silicone around the dividers where mine had much more. Prob three coats and I used my fingers to work it into all the little nooks and cranny's to make sure it got in there good. I let it dry for 24 hours after each application. So what are your thoughts/tips/tricks?
Also does anyone know where I might be able to find any foam like in the pic?
|11-03-2013 05:37 PM|
|SlammedDC2||Hey guys, it's been awhile but I did some updating to the OP.|
|10-01-2013 03:47 PM|
Whee clubs...this is my second sump build. #23 ?
In progress pics, but almost done.
Very much a budget build, and yes I know the return pump situation is 'less than ideal'. This is a 50G tank, going under a 125G display.
|09-20-2013 02:54 AM|
|Land_lubber||Oh I have lids on my sump as well to help reduce evaporation and keep the heat in as well. Thinking of insulating the back and sides of the sump to help with heat as well.|
|09-20-2013 02:52 AM|
Nice, here is my sump
The overflow goes into the left where the bio balls are and from there goes through different coarse porat foam before heading back up through the return on the far right.
|This thread has more than 15 replies. Click here to review the whole thread.|