The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment > Suction Cups Stiffening

Thread: Suction Cups Stiffening Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-07-2013 06:37 PM
Hmoobthor i use zoo med mag clip for all my intake and heaters and spray bar
02-07-2013 05:45 PM
CrypticLifeStyle You can hot glue magnets to the plastic holder, and put the other attachments on the outside of the glass. Gives a nice clean look, but success will determined by the magnet strength.
02-06-2013 04:43 PM
latchdan Thanks for the ideas, I might give the acrylic a go and see how it works.
02-06-2013 02:20 AM
talontsiawd I find that boiling almost always works. If not, it usually means that the suction cup has some film or the glass has something on it. I will bleach and scrub the suction cup and clean that part of the glass with a credit card, even if I have cleaned it with a scrubber already. Usually if you do those three things, you can get them to work like new.
02-06-2013 01:21 AM
deeda If you like DIY projects, you can make an acrylic hanger for your heater, intake/output pipes and possibly powerheads.

I made my first hanger using a clear acrylic wreath hanger cut to size. I have since just used narrow strips of acrylic cut from a large sheet and use a heat gun to warm the acrylic so it can be bent into a hook that hangs on the rim of the aquarium.

Here is a completed heater holder using the stock Eheim holder minus the suction cups.

Side view



Back view



I removed the suction cups and drilled the posts to accept #4 x 1/2" long stainless steel pan head phillips screws.



Measure the distance from the top of the hook to where you want the heater mounted on the acrylic holder and drill holes through the hanger, using the heater holder to mark the spots.



This is a very simple project to do and I have used it for both holding heaters and canister intake/output piping. I have not tried it for powerheads because they usually aren't mounted on the rear of the aquarium.

If you use glass canopies or hoods, you will be limited on where you can place the acrylic holder because it needs to hang on the rim of the aquarium.
02-05-2013 10:44 PM
leonardcarlson Put some water in a bowl, suction cups in the water, and microwave for,two minutes, they are as good as new, same as boiling them
02-05-2013 08:58 PM
Green_Flash time to replace?
02-05-2013 08:53 PM
cichnatic I normally just boil it with water like you did. My suction cups are mainly eheim brand and they stick for quite awhile. I haven't need to boil them for the past couple of months.
02-05-2013 08:21 PM
latchdan
Suction Cups Stiffening

So what does everyone do when the suction cups on the heater/powerheads/filter intake & return just don't stick anymore? I normally put them in boiling water to soften them up, but this seems to only work for a couple more days before they start falling off the glass.

I bought some magnet ones but they don't fit anything right.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 12:41 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012