|01-22-2013 11:51 PM|
|veganboyscout||Shalu, I thought some more on these calculations, and I realized that when calculating the efficiency we should use the proportion that the wattage increased, not the 1x, 2x, 3x, 4x because the power did not increase in practice or in reality by double, triple, quadruple, as we attempt to do by overdriving the lights. We know this thanks to your use of the Kill-A-Watt. So, for the T8 bulb at 4x overdrive, the OD Efficienies calculation would look like 4.6/(3.8*(69/40))=.70 or 70% efficiency. So, as 100% efficiency for 1x as the basis, for all the T8 OD Efficiencies, I calculated 2x = 85%, 3x=78%, 4x=70%. These figures are in agreement with estimates elsewhere on the web.|
|01-21-2013 06:36 AM|
|veganboyscout||hey Shalu, I think you were using the wrong formula to calculate "OD Efficiency" in column 5. I believe you should have divided the lumen/watt figure by 1, 2, 3 or 4 X the lumen/watt figure for the 1 X test (respectively). For example, The "OD Efficiency" for the T8 bulb at 4X overdrive should be 4.6/(4x3.8)=.30 According to your data, you should have concluded that T8 bulbs at 4X overdrive are less than 1/3 as efficient as 1X factory T8 bulbs. Your conclusions were completely wrong. Fluorescent bulbs do become markedly less efficient the more you overdrive them, not more! Your own data demonstrates that! I wish you were right, but you are not. Does anybody else agree with me?|
|05-06-2009 11:18 PM|
so what about overdriving a standard t-5 ballasts and bulbs i'm o.d.ing a standard t-5 x2
28w bulb it looks a little brighter and a little whiter can i expect better results useing this bulb instead of a factory o.d. 54w bulb
|10-14-2008 07:38 AM|
Switching into a electronic ballast rather than a noraml ballast will helps save at least 30% of the electricity consumption as well..
|09-13-2008 11:41 PM|
|Basilisk||Just as I thought.|
|09-13-2008 09:57 AM|
|epicfish||No, it's not possible.|
|09-13-2008 09:27 AM|
I haven't overdriven yet. However, reading over and over this article, leaves me wondering what could be achieved ODing using several single bulb ballasts. I have 4 of them. Do you think that could overdrive actual 2x? I mean, actual 64 watts into one bulb with two ballasts?
I fear, without a solid basis, that two ballasts won't work in perfect sync, and cause some serious strike or shock.
|08-09-2008 01:46 AM|
Thanks for the very awesome thread. Most of what I saw so far was the assumption that energy would be wasted. I'm moving forward now with my ODNO project.
I only wish that 2 bulbs were tested @ 2x ODNO to see it the ballast provided the 112watts? or less than 100w
|06-10-2007 07:04 PM|
Thanks for that. I was hoping to be able to overdrive them, but I think I'll forget it now. I just needed a little more light output.
|06-10-2007 05:15 AM|
|milkdud||What reflectors are you using for the t8's?|
|06-09-2007 04:05 PM|
|SCMurphy||PC bulbs are basically already on overdrive, it isn't worth the electricity to overdrive them more, the efficiency drops.|
|06-09-2007 12:44 AM|
|PAINKILLER1009||Looks like compact florecent bulb to me. You can over drive them but they run very hot and you cant make them very much brighter. ODing is for t12-t8 really.|
|06-08-2007 01:44 PM|
Will ODNO work with this kind of lamp:
As far as I can tell it's the same technology as the regular tubes, just with a 180° bend in it...
|01-08-2007 09:56 PM|
|Freebird01||with an ODNO setup can you still use the bulb sleeves or do the bulbs get too hot for them?|
|03-07-2006 12:10 AM|
Really nice testing Shalu. Just to make a point about cheap, I bought a Shoplight (the brand) from Home Depot that has an electronic ballast and burns two 48", T8 bulbs (32 watts each). This cost $7.50. After reading the article, I did a search for electronic ballasts on the internet, and the lowest price I found for a 2 bulb, T-8 32 watt was $5.66. With shipping, not worth it. So I just bought another Shoplight, cannibalized the ballast, and hooked it to the orignal shoplight, overdriving both bulbs 2X. This is one bright aquarium light! It's definitely brighter than my 2x55 watt AH supply bright kit. It was very easy to hook up. Just two small holes drilled in the shop light to bolt in the ballast. No extra wire needed, or even any connectors. All that were needed were already in the Shoplight. Even the holes to plug the two wires in are already on the bulb end caps.
I was worried about heat, but the light is still much cooler than the AH kit, and I can grab the light anywhere without fearing it will be too hot to handle.
|This thread has more than 15 replies. Click here to review the whole thread.|