The Planted Tank Forum - Reply to Topic
Planted Tank Forums
Your Tanks Image Hosting *Tank Tracker * Plant Profiles Fish Profiles Planted Tank Guide Photo Gallery Articles

Go Back   The Planted Tank Forum > Specific Aspects of a Planted Tank > Equipment > Running co2 to two aquariums.

Thread: Running co2 to two aquariums. Reply to Thread
Title:
  
Message:
Post Icons
You may choose an icon for your message from the following list:
 

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-20-2012 09:20 PM
talontsiawd You can find a bunch of manifolds to fit your needs. The easiest way is two needle valves if you photo periods are similar (you can have some CO2 running before the lights go on in one tank, for example, or a bit after). Or you can have a full post regulator for each tank (solenoid, bubble counter, needle valve).

Most people use 1/8 NPT fittings so you don't really even need a manifold. You can just buy a splitter at a hardware store. You really can buy all your fittings at a hardware store and just add your needle valves, solenoids, etc).


You could theoretically just use a splitter if the tanks were the same size and had the same diffusor/reactors. These are cheap and easy to find. There is a chance you could run into problems as the CO2 will take the path of least resistance. I doubt two diffusors would have enough variance to make a big difference, even less with a reactor. But there is always that chance. Add a different amount of plant mass and their could be issues, especially if you are on the cusp of gassing your fish. One mistake and you are in trouble. I would just spend the money on an extra needle valve and manifold/splitter, even on identical tanks.
02-20-2012 07:45 PM
nokturnalkid If u want ultimate flexibility, add another solenoid too. That way each tank is comletely independent of each other. You dont have to worry if one tank has a longer photoperiod than the other
02-20-2012 07:03 AM
Aquaticfan Exactly as others have mentioned. Ive got my 20 Gallon and my 46 gallon tanks on the same Co2 set up.

Single solenoid that connects to a manifold and 2 output needle valves. If you had more then just the 2 you wanted to do you could even do more. Just have to add to the manifold and more needle valves.
02-20-2012 04:38 AM
Capsaicin_MFK BAM! Two tanks, one co2 source.

02-20-2012 12:39 AM
samamorgan As i said, look at bettatail's thread. There is a plethora of information on this forum if you just open your eyes and take a gander.
02-20-2012 12:34 AM
Zefrik How do you get two needle valves connected to the regulator?
02-20-2012 12:33 AM
samamorgan Two needle valves from your regulator. Need a manifold. Check bettatail's thread.
02-20-2012 12:29 AM
Zefrik
Running co2 to two aquariums.

How can I run co2 to two aquariums. I will put a Microsoft paint sketch of where the tanks are situated. I was thinking about using a "T" splitter. But I don't know how I could monitor and adjust the amount of co2 between the tanks. I have a cheap plastic 4 way gang valve that I got at petco for air pumps but I feel it might not be strong enough to be used with pressurized co2. Is there like a cheap or diy manifold of some sort that could be used.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT. The time now is 01:08 AM.


Powered by vBulletin®
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright Planted Tank LLC 2012