|06-01-2011 02:00 AM|
|Coverfire||That's what I was asking, thank you. The seller I bought it from called it a 3818 but the regulator tag said 3810-580 which I thought that indicated the indivudal model. That is honestly more preferable because the 3810 has a more useable range for planted tanks.|
|05-31-2011 10:54 PM|
The arrow is pointing to what you've got. The other string of numbers is the build number.
|05-31-2011 07:00 PM|
|Coverfire||Any thoughts on whether the tag that says 3810-580 is for the specific model number or just the series it is in?|
|05-30-2011 12:42 AM|
|05-29-2011 08:39 PM|
|05-29-2011 08:33 PM|
|05-29-2011 07:55 PM|
the matheson 3810 is a 100psi regulator. it came with a 200psi gauge.
the 3816 has a 400psi gauge.
(google matheson 3810 and look for the pdf)
|05-29-2011 04:05 PM|
|Hoppy||A 0-400 psi output regulator is not a good CO2 regulator, for our uses. We need to adjust the pressure to 10-30 psi, which would not read at all accurately on a 400 psi gauge. You can use a lower pressure gauge, but then you stand a very good chance of overpresssuring it and ruining it.|
|05-29-2011 07:03 AM|
The bay ID, western stainless steel nipple and nut
|05-29-2011 06:51 AM|
Stainless CGA320 nipple (>2"): $24
Stainless CGA320 nut: $24
Stainless in-port filter: $13
All plus shipping.
Pm me for the website.
COntact customer support at Matheson and ask them for the proper part number. Stainless is more expensive than brass generally speaking. But a stainless gauge (new) will run you about $50. You can try to find a used one, but good luck...these stainless units are harder to find. They are not like a model 8.
Sometimes the replacement gauges will not match exactly. If you're a stickler like I am, you can replace both gauges at the same time and save the good gauge for the next vintage regulator you pick up.
Again, PM me if you need any help.
|05-29-2011 05:22 AM|
You can get the cga 320 nipple and nut from airgas for under $10. If you want the stainless steel nipple and nut, go to evil bay, the price is about $40-$50.
The LP gauge, it is hard to find a stainless steel one, probably you can order it from airgas, not cheap.
if you want a regular brass 0-400 psi from evil bay, have to wait until you see one.
|05-29-2011 04:58 AM|
|Coverfire||I thought about it but my local shops probably don't stock it and I am afraid that ordering it might be a bit pricey. I'm not opposed to finding a used one and have been scouring ebay for one.|
|05-29-2011 04:56 AM|
|jkan0228||Maybe go to the wielding shop for the gauge?|
|05-29-2011 04:52 AM|
Matheson 3810 Build
I recently acquired a Matheson 3810 stainless regulator, however it does not have a low pressure gauge and I need to switch out the stem on it (cga 580) to a cga 320.
Where is the best place to obtain a low pressure gauge that is a 316 stainless Matheson gauge with a range from preferably 0-400 psi because I would like to keep it as original as possible?
Additionally I would like to find a short stainless cga nipple and nut because I only have a 5lb tank and I am worried that it might tip over from the weight of the regulator with too long of a stem. I am having trouble locating this and considered using an adapter but it would only add length to the setup.
After I finish with the regulator I will likely piece together a post body kit consisting of a Clippard Mouse solenoid and a Swagelok metering valve. I would appreciate some input on this and the best method of constructing that setup.