Running co2 to two aquariums. - The Planted Tank Forum
 
LinkBack Thread Tools Display Modes
post #1 of 8 (permalink) Old 02-20-2012, 12:29 AM Thread Starter
Wannabe Guru
 
Zefrik's Avatar
 
Join Date: Oct 2011
Location: Topeka, Kansas
Posts: 1,026
Running co2 to two aquariums.

How can I run co2 to two aquariums. I will put a Microsoft paint sketch of where the tanks are situated. I was thinking about using a "T" splitter. But I don't know how I could monitor and adjust the amount of co2 between the tanks. I have a cheap plastic 4 way gang valve that I got at petco for air pumps but I feel it might not be strong enough to be used with pressurized co2. Is there like a cheap or diy manifold of some sort that could be used.
Zefrik is offline  
Sponsored Links
Advertisement
 
post #2 of 8 (permalink) Old 02-20-2012, 12:33 AM
Wannabe Guru
 
samamorgan's Avatar
 
Join Date: Dec 2011
Location: Seattle, WA
Posts: 1,235
Send a message via MSN to samamorgan Send a message via Skype™ to samamorgan
Two needle valves from your regulator. Need a manifold. Check bettatail's thread.

LED Lighting Compendium
Quote:
Originally Posted by Ludwig van Beethoven
Don't only practice your art, but force your way into it's secrets, for it and knowledge can raise men to the divine.
samamorgan is offline  
post #3 of 8 (permalink) Old 02-20-2012, 12:34 AM Thread Starter
Wannabe Guru
 
Zefrik's Avatar
 
Join Date: Oct 2011
Location: Topeka, Kansas
Posts: 1,026
How do you get two needle valves connected to the regulator?
Zefrik is offline  
post #4 of 8 (permalink) Old 02-20-2012, 12:39 AM
Wannabe Guru
 
samamorgan's Avatar
 
Join Date: Dec 2011
Location: Seattle, WA
Posts: 1,235
Send a message via MSN to samamorgan Send a message via Skype™ to samamorgan
As i said, look at bettatail's thread. There is a plethora of information on this forum if you just open your eyes and take a gander.

LED Lighting Compendium
Quote:
Originally Posted by Ludwig van Beethoven
Don't only practice your art, but force your way into it's secrets, for it and knowledge can raise men to the divine.
samamorgan is offline  
post #5 of 8 (permalink) Old 02-20-2012, 04:38 AM
Planted Tank Enthusiast
 
Capsaicin_MFK's Avatar
 
Join Date: Nov 2009
Location: Minnesota
Posts: 785
BAM! Two tanks, one co2 source.


Mage - The other hobby
No planted tanks currently running (11/26/2014)
Capsaicin_MFK is offline  
post #6 of 8 (permalink) Old 02-20-2012, 07:03 AM
Wannabe Guru
 
Aquaticfan's Avatar
 
Join Date: Oct 2011
Location: USA
Posts: 1,200
Exactly as others have mentioned. Ive got my 20 Gallon and my 46 gallon tanks on the same Co2 set up.

Single solenoid that connects to a manifold and 2 output needle valves. If you had more then just the 2 you wanted to do you could even do more. Just have to add to the manifold and more needle valves.

Sun Sun pimp #72
RAOK CLUB # 68

Conway
Aquaticfan is offline  
post #7 of 8 (permalink) Old 02-20-2012, 07:45 PM
Wannabe Guru
 
nokturnalkid's Avatar
 
Join Date: Apr 2007
Location: HI, but Pueblo, CO for now
Posts: 1,241
If u want ultimate flexibility, add another solenoid too. That way each tank is comletely independent of each other. You dont have to worry if one tank has a longer photoperiod than the other

Schuber Wright 6 gal
Mr. Aqua 11.4 g...coming soon
30gal Journal - RIP
nokturnalkid is offline  
post #8 of 8 (permalink) Old 02-20-2012, 09:20 PM
Planted Tank Guru
 
talontsiawd's Avatar
 
Join Date: Oct 2008
Location: Concord, CA
Posts: 4,576
Send a message via AIM to talontsiawd
You can find a bunch of manifolds to fit your needs. The easiest way is two needle valves if you photo periods are similar (you can have some CO2 running before the lights go on in one tank, for example, or a bit after). Or you can have a full post regulator for each tank (solenoid, bubble counter, needle valve).

Most people use 1/8 NPT fittings so you don't really even need a manifold. You can just buy a splitter at a hardware store. You really can buy all your fittings at a hardware store and just add your needle valves, solenoids, etc).


You could theoretically just use a splitter if the tanks were the same size and had the same diffusor/reactors. These are cheap and easy to find. There is a chance you could run into problems as the CO2 will take the path of least resistance. I doubt two diffusors would have enough variance to make a big difference, even less with a reactor. But there is always that chance. Add a different amount of plant mass and their could be issues, especially if you are on the cusp of gassing your fish. One mistake and you are in trouble. I would just spend the money on an extra needle valve and manifold/splitter, even on identical tanks.
talontsiawd is offline  
Reply

Tags
aquariums, co2, gang valve, manifold, multiple

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome