Issues I'm having and solutions I'm considering - The Planted Tank Forum
LinkBack Thread Tools Display Modes
post #1 of 3 (permalink) Old 11-11-2012, 11:52 AM Thread Starter
Algae Grower
Join Date: Jun 2012
Location: Ohio
Posts: 95
Issues I'm having and solutions I'm considering

30 gal
T5HO dual bulb on 8 hrs/day (I use a layer of window screen to lower the light intensity)
Fluval 206
Liquid carbon
Regular fert dosing
30 - 50% WC every week
Indian sword

My tank has been doing okay, however I've been having BBA creeping up and now I have wendtii leaves melting like crazy. At one point I had decided to do injected CO2, but the first set up I purchased wasn't quite right so I returned it, then I got busy at work and wasn't able to move forward with that plan, and then got honest with myself and decided I really don't want to do a high-tech set up.

Over the months, I have tried experiments one at a time like decreasing the photoperiod, removing the light diffusing screen, raising the lights, increasing nitrates, etc, etc, and haven't come up with a solution that truly creates a worry free tank. I got to the point where I started worrying about the plants more than the fish, and that wasn't the reason that I got into this hobby.

So here's where I'm at with the options I'm considering. I ranked them from most likely to least likely to solve my problem:

1. Get rid of the plants altogether and purchase fake plants. I know this doesn't remove the opportunity for algae, but I would bet there are specific ways that I can deal with algae in a plant free tank (like black-outs, etc). I really pray to God that there are some attractive fake plants out there that look better than the ones I see in the LFS stores.

2. Purchase a lower intensity light set up. This would cost money as lights aren't cheap. I spent $130 on this light set up at the suggestion of the person who sold me the tank, and it's probably the worst decision I made in this whole hobby. It's just too much light, and my attempts to lower the light by raising the fixture (which is problematic) or diffuse the light with a layer window screen have proved ineffective.

3. Rescape with new plants, but I know that this would be a losing battle because I need to deal with the algae not the plants.

annewaldron is offline  
Sponsored Links
post #2 of 3 (permalink) Old 11-11-2012, 02:03 PM
Planted Tank Obsessed
mommabear1007's Avatar
Join Date: Nov 2011
Location: under a dead ohio sky
Posts: 311
if you dont want co2 i would think you would need to replace the light fixture with something less intense. you can get some work lights at home depot or lowes that use cfls. they are relatively inexpensive. then you could either sell what you have or keep it in case you change your mind about staying low tech. i think the light is your biggest issue right now, though.

you could try adding more plants to use up that light. you could also try giving the photoperiod a break: 4 hours on, 3 hours off, 3 hours on, something like that. liquid carbon melts some plants, which might be why the wendtii leaves are melting.

surely someone else will have better advice. i'm not exactly experienced enough to give advice, just trying to help. i have had a t5ho on a 29 gall and had all kinds of problems until i got the pressurized co2 and ferts. i still have to give the photoperiod a break for a couple of hours a day to prevent the BBA from taking over. i also spot treat with h2o2 when doing water changes but i would rather not do that on a regular basis. i am finally getting it taken care of. i think the h2o2 and the break in the photoperiod have been most useful as the addition of co2 alone did not help much (although my plants loved it).

I have gone to a place far below up above and in between the middle.
mommabear1007 is offline  
post #3 of 3 (permalink) Old 11-11-2012, 05:24 PM
Planted Tank Guru
Join Date: Dec 2005
Location: Sacramento, CA
Posts: 21,015
From my experience with BBA, if you reduce the light level to 20-25 micromols of PAR at the substrate, and use CO2 at a relatively low bubble rate, so you never need to worry about hot it affects the fish, BBA is not a problem. Even if it shows up, it will grow so slowly you have plenty of time to schedule a BBA cleanup - shutting down the filter, lowering the water level, then squirting a tanks dosage of Excel mixed in a cup of water over all of the BBA to kill it. It does come back, but it takes a month or so to do it. Many plants will grow well, but slowly, at that light level too.

You can look at the charts in Lighting an Aquarium with PAR instead of Watts to get a good idea of how much PAR you have, or, much better, borrow a PAR meter to test it.

If you use plastic plants, and the same light level, you will still get BBA at the same rate. The only thing you gain is that you can't kill plastic plants with BBA.

Hoppy is offline  

Quick Reply

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome