I think this has been discussed in a few threads but not really documented clearly, so I figured a DIY write-up could be helpful. I'm currently using this method to inject CO2 on a Fluval Edge (which comes with an AC20 / Mini HOB), but it should work on any AquaClear HOB. In contrast to bubbling the CO2 directly into the filter intake, this configuration keeps the airline out of the tank and avoids impeller gurgling noises.
Inside the filter, there is an impeller cover. Pull this out, noting the hole that is used to expel air when priming the filter.
The plan is to insert airline through the hole in the impeller cover and attach a diffuser to the other end. I used a broken chopstick piece. Another alternative is the Lee's discard-a-stone "slim", seen here. The space is pretty constrained so options are limited.
The airline and diffuser fit through the impeller cover like this:
Now, reinsert the impeller cover. You want the diffuser to stick out like this...it injects into a narrow column of water between the filter basket and the impeller motor housing
Note: the hole that we plugged up with airline tubing was there so air could escape while priming the filter. So we need a different way to expel the air trapped below the impeller cover and prime the filter. Solution: pull the filter basket tab in this direction while the filter is priming:
Its like a mini-CO2 reactor. Bubbles get jostled around the downflow and anything that is undissolved is trapped below the sponge. At least for me, the CO2 diffuses at a sufficient rate that a big CO2 bubble doesn't form.
I've been injecting my CO2 into the AC20's intake for a while now, but the only thing missing is the chopstick. Will DIY generate enough pressure for this to work?
I've been injecting my CO2 into the AC20's intake for a while now, but the only thing missing is the chopstick. Will DIY generate enough pressure for this to work?
Was looking for ways to improve the diffusion rate of the system without upping the bubble count so decided to give the ADA "ball glass" diffuser a try.
This piece is different from other ADA diffusers in that the bubbles are not emitted directionally but rather radiate uniformly from a point source. For this purpose it fits perfectly: its a nudge over 4" long (long enough to stick out of the top of the filter) and the ball is maybe 3/8 in diameter (small enough to fit under the impeller cover).
Essentially, we're just replacing the chopstick from the prior post with the ball glass. However, the diameter of the glass stem on the Ball Glass diffuser is larger than the hole we were using before. So it needs to be drilled / reamed out. Since I was getting out the drill anyway, I decided to relocate the hole to increase the water contact time. Here you can see the hole I drilled near the lower left edge of the impeller cover. Drill a small hole then test fit the glass stem and drill again (I actually drilled the hole a tad too large). If you don't have a drill I'm pretty sure you could ream this out with an Exacto knife as the plastic is very soft.
This is what the impeller cover looks like with the ball glass inserted:
Does it work any better? Well, my HC pearls more consistently which is positive but the finer bubbles produced by the ceramic diffuser find their way through the filter more easily too (ie contributing to some fizz in the water).
Going to try to run more concrete tests (probably time versus pH) over the long weekend comparing the two diffusers.
If you needed to hold it up in place you could put a rubber O ring or 2 from the hardware store over the tube and slide them down to the plastic cover.
I picked up that diffuser today from ADA. It was $50 !!! Ouch. Anyway, I am curious to know how this system is working for you or if I should consider using another method?
I did this modification, but I didn't have any diffuser to use so I just left the tubing open to bubble inside the filter. Unfortunately the CO2 bubble didn't seem to stay in the filter like that and bubble right back out of the filter through the middle section, so I wasn't seeing much if any difference in my CO2 levels as a result. I suppose they might stay within the filter better if they were much smaller.
I now have my CO2 off though, as I couldn't get any sort of a consistent bubble rate and one day discovered that my rate of a bubble every few seconds had turned into constant CO2 stream which would have suffocated my fish if I hadn't reacted immediately. So I'm looking for a new needle valve now to add in-line.
I bought an inexpensive ceramic disk nano diffuser, but it looks larger than it did in the photo and still doesn't fit under that plate by the impeller. So I was about to start to modify it by sawing it into sections and then reassembling it, but then I went and rummaged through the kitchen until I found a chopstick. Chopstick piece works fine, but it does make a little almost squeaky noise whenever bubbles come out.
By the way, how many bubbles per second do you find to be the best in order to achieve 20-30 ppm in an Edge?
Great mod. I actually did this with my filter a few months ago, but I didn't put a diffuser in at all, just stuck the tubing through the hole. The impeller chops it up and it gets caught in the media. Works like a charm.
I also turn off the filter every day to feed baby brine, and when I power it back up it is still able to prime, even with the hole clogged.
Don't you get a lot of CO2 offgassed as the water flows out the filter? I would imagine that it would be difficult to keep up the amount of CO2 in the water column.
possibly show a step by step video on how to do this? im the type of person that wants to make sure im doing it right lol ihave a aqua clear hob filter and this would be a great addition!
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
The Planted Tank Forum
3.5M posts
130.6K members
Since 2002
A forum community dedicated to Aquatic tank owners and enthusiasts. Come join the discussion about flora, fauna, health, housing, filters, care, classifieds, and more!