40x Cree XP-G LEDs - Which material to use as tank lid? - The Planted Tank Forum
LinkBack Thread Tools Display Modes
post #1 of 2 (permalink) Old 01-05-2013, 05:39 AM Thread Starter
Algae Grower
PTrader: (0/0%)
Join Date: Jun 2012
Location: Australia
Posts: 16
40x Cree XP-G LEDs - Which material to use as tank lid?


I am just about to complete my DIY LED build using the RapidLED 36x CREE XP-G LED kit. I am driving 32 Cool White and 4 Warm White LEDs (using the 80 degree optics) at 1000 milliamps as well as the RapidLED Moonlight kit (4x Blue LEDs) at between 150 and 350 milliamps (they have no optics).

Edit I am driving 3x Meanwell ELN-60-48P LED Drivers using an Arduino controller. I will dim them on and off for simulated sunset. I have the Drivers set to 1000 milliamps so that is the maximum they will go to (although I may go up or down slightly once I test out the lighting) but they won't be at 1000 milliamps ALL of the time due to dimming schedules. Edit

I am retrofitting my Aqua One 120 tank (120 centimetres wide, ~90 Gallons) and I'm wondering what material I can use as a lid.

I have 3 rows of LEDs (12 XP-G LEDs in each) and the optics are really close to the surface of the hood (ie; they almost extrude from the hood). I can place a material underneath the hood, resting on the tank.

I have the choice of glass (I assume 1.5mm or 2mm thick) however it will be hard to get as I'll need to have it specially cut. My local hardware store also has other options that I'm more interested in (for lower weight). These are PVC and Polycarbonate.

There are sheets used for roofing (skylights) that I can buy. The PVC is flat and 3mm thick and very, very clear. The polycarbonate is corrugated and very thin (and clear but light could get distorted due to the corrugation). The Polycarbonate mentions that it has high heat resistant properties (due to it being skylight roofing).

Could someone please give me some advice as to which plastic material they feel is best for my needs. The LEDs won't get too hot I assume (they are mounted to 3mm thick aluminium "U" channel (40mm wide, 25mm deep and 3mm thick) so the "heatsinking" ability of it is very good.

Basically I know that Polycarbonate is a good choice but the corrugation is a downside. I'm also not sure about PVC under high heat or ligght (I don't want it to melt, bubble or go yellow/fade under my lights). Glass is too expensive, needs to be custom made, breakable and also heavy.

Any advice would be most welcome as I will purchase very soon to finish my project. Thanks!

Last edited by Simpsoid; 01-05-2013 at 05:43 AM. Reason: Info about LED Driver currents
Simpsoid is offline  
Sponsored Links
post #2 of 2 (permalink) Old 01-05-2013, 05:53 AM
Algae Grower
Miles03's Avatar
PTrader: (1/100%)
Join Date: Feb 2012
Location: Las vegas, nevada
Posts: 38
Short answer go with the glass, maybe harder to source but overtime you will not regret it. Polycarbonate overtime can warp especially thinner sheets exposed to high amounts of humidity. The PVC u are referring is it acrylic in America? Because that would be my second choice besides the glass. Post some pics of the lights interested in seeing your layout.
Miles03 is online now  

cree, leds, lid, material

Quick Reply

Register Now

In order to be able to post messages on the The Planted Tank Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome